Technical Data; Noise Information - REMS Swing Instrucciones De Uso

eng
unit when they are older than 16, when this is necessary for their training,
and under the supervision of a trained operative.
Keep the work area tidy. Clutter can prove dangerous.
•
Do not expose the unit to rain or to damp or wet surroundings. Store the
•
unit where it is dry and safe.
Provide adequate lighting at the workplace.
•
Wear suitable work clothes, keep long hair well clear, take off gloves,
•
jewellery and similar.
Use personal safety equipment (e. g. safety glasses, ear protectors).
•
Keep bystanders away, especially children.
•
Keep hands away from moving (rotating) parts.
•
Take up a firm standing position during operation.
•
Check the unit occasionally for damage, and to see that it is operating correctly.
•
Replace worn parts as early as possible.
•
Only use genuine spare parts and accessories, for personal safety rea-
•
sons, to ensure correct operation of the unit, and to preserve the basis for
warranty claim.
All unauthorised modifications of the unit are prohibited for safety reasons.
•
All repair work must be performed only by specialist personnel or by per-
•
sons familiar with the unit.

1. Technical Data

1.1. Article numbers
Bending formers
Bender drive
Universal crossbar 10–26 (
Crossbar 32
Steel case
Device for reverse bends on installed pipes
1.2. Capacity
Soft copper tubes, also thin-walled
Coated soft copper tubes, also thin-walled heating tubes
according to DIN EN 1057
Coated C-Stahl tubes of pressfitting systems
Soft precision steel tubes according to DIN 2391–2394
black or coated
Muliti-layer composite tubes
Hard copper pipes have to be annealed!

1.3. Noise information

Emission at workplace
2. Setting up
Put the crossbar (1) on the bender unit (2), so that the sliding pieces (3) for
the desired pipe size are positioned towards the dented rod (4). The sliding
pieces are marked with the various pipe sizes. Fasten the crossbar with the
wing screw (5). Choose the correct former (6) and put it on the ratchet bar
(4). Press the feed lever (7) in indicated direction (8) downwards and push
the former (ratchet bar) back towards the handle. Release feed lever (7).
3. Operation
Turn the sliding pieces (3) as such, that the related radius of the indicated
pipe size is positioned opposite the former. Put the pipe in between the form
and sliding piece. Press feed lever a few times in indicated direction (8) and
drive the former as far as desired. Push the feed lever towards indicated
direction (8) and push the form if necessary with the bent pipe backwards.
Take the pipe out.
The upper side of the formers (6) show marks (9), which allow precision
bending. To this the marking point where the bend should end has to be posi-
tioned to the marking (9).
Attention! The formers and the sliding pieces are made of glass-fibre rein-
forced polyamide. This artificial material has a special positive sliding effect,
is highly-tensile and resistant to heat up to app. 150°C. Annealed copper
pipes should therefore be cooled down to below this temperature.
All manuals and user guides at all-guides.com
3 / – 7 / )
8 8
Ø 10 – 22 mm
Ø 10 – 18 mm
Ø 12 – 18 mm
Ø 10 – 18 mm
Ø 14 – 32 mm
4. Service / Repair
The unit is maintenance-free, no service required.
5. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to
the first user but shall be a maximum of 24 months after delivery to the Dealer.
The date of delivery shall be documented by the submission of the original
purchase documents, which must include the date of purchase and the de-
signation of the product. All functional defects occurring within the warranty
period, which clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the guarantee period for the product. Damage attributable to natural
wear and tear, incorrect treatment or misuse, failure to observe the opera-
tional instructions, unsuitable operating materials, excessive demand, use
for unauthorized purposes, interventions by the Customer or a third party or
other reasons, for which REMS is not responsible, shall be excluded from
the warranty.
Services under the warranty may only be provided by customer service sta-
tions authorized for this purpose by REMS. Complaints will only be accep-
ted if the product is returned to a customer service station authorized by
REMS without prior interference in an unassembled condition. Replaced pro-
ducts and parts shall become the property of REMS.
see table
The user shall be responsible for the cost of shipping and returning the
153100
product.
153125
The legal rights of users, in particular the right to claim damages from the
153115
Dealer, shall not be affected. This manufacturer's warranty shall apply only
153265
to new products purchased in the European Union, in Norway or Switzerland.
153140
fra A lire avant que de mettre l'appareil en
Ø 3 / – 7 / "
8 8
service!
s ≤ 1 mm
Cet appareil a été conçu et fabriqué selon les plus récentes connaissances
techniques et en tenant compte des règles de sécurité en vigueur. L'emploi
Ø 3 / – 5 / " abusif ou inapproprié de l'appareil peut cependant être la source de dangers
8 8
s ≤ 1 mm
aussi bien pour l'opérateur que des tiers se tenant dans son voisinage, ou
causer des dégâts matériels. Pour cette raison, lire attentivement les re-
marques relatives à la sécurité!
Remarques concernant la sécurité générale
s ≤ 1 mm
N'utiliser l'appareil que pour accomplir les tâches pour lesquelles il a été
•
spécialement conçu, et se conformer aux prescriptions élémentaires re-
latives à la Sécurité du Travail et à la Prévention d'Accidents.
L'appareil ne doit être opéré que par du personnel spécialement formé.
•
Apprentis ou jeunes gens ne peuvent utiliser l'appareil que s'ils sont âgés
70 dB (A)
de 16 ans au moins, uniquement dans le cadre de la Formation Profes-
sionnelle, et à condition d'être surveillés par un instructeur qualifié.
Toujours maintenir le poste de travail bien rangé: le désordre est un fac-
•
teur d'accidents!
Ne pas exposer l'appareil à la pluie, ni l'utiliser dans une atmosphère
•
humide ou mouillée. Toujours entreposer la machine dans un endroit sec
et protégé.
Assurer un éclairage suffisant au poste de travail.
•
Porter des vêtements de travail appropriés, protéger par un casque ou
•
nouer des cheveux longs, éviter le port de gants et de bijoux ou penden-
tifs quelconques.
Utiliser autant que possible des équipements de protection personnelle:
•
lunettes, casques insonorisants, par exemple.
Tenir éloignées toutes tierces personnes, enfants en particulier.
•
Ne jamais empoigner ou intervenir sur une pièce en mouvement.
•
Veiller à prendre une positon de travail correcte et sûre.
•
Contrôler périodiquement le bon état de l'appareil et s'assurer de son
•
fonctionnement correct.
Remplacer immédiatement toute pièce usée ou endommagée.
•
Pour votre sécurité personnelle, pour l'utilisation de l'appareil aux fins pour
•
lesquelles il a été prévu, et également pour justifier d'éventuelles reven-
dications de garantie, n'utiliser que des accessoires et des pièces de
rechange d'origine.
Pour d'évidentes raisons de sécurité, toute intervention ou modification
•
de l'appareil, sans notre assentiment exprès donné par écrit, est for-
mellement interdite.
eng / fra