Operation - EINHELL GE-SA 1335 P Manual De Instrucciones

Mounting the catch basket (see Figs. 5a/5b)
•
Pull the rubber clips over the metal frame (Fig.
5a).
•
To hang the catch basket on the scarifier you
must lift the ejector flap (Fig. 5b/Item 5) with
one hand and with the other hand take hold of
the catch basket by the handle and hook it in
place from above.
Danger!
Before you ever hook the catch basket in place
you must ensure that the cutting unit is not rota-
ting!
Adjusting the handlebar height (see Fig. 6)
On both sides of the scarifi er undo the quick-lock
levers (Fig. 6/Item 11).
The height of the handlebar can be set to position
1 or 2 (Fig. 6) during operation. You must then
tighten the quick-release fasteners again.
The same tilt angle must be set on both sides.

6. Operation

Note!
The engine comes without oil and petrol.
Therefore, be sure to add oil and petrol before
starting the engine.
1. Check the oil level (see 7.2).
2. Use a funnel and measuring jug to fi ll the tank
with petrol. Make sure that the petrol is clean.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch off the
engine before refueling and allow the engine to
cool down for a few minutes.
3. Ensure that the ignition cable is connected to
the spark plug.
4. The cutting mechanism must move freely in
order to start the equipment. Move the depth
setting to position 0.
Starting the engine
Omit point 1 and point 2 if the engine has already
warmed. Begin the starting procedure at point 3.
1. Pump the fuel pump „Primer1" (Fig. 9a/Item
16) six times.
2. Pump the cold start pump at the carburetor
(Fig. 9b/Item 17) ten times.
3. Pull the engine start/stop lever (Fig. 9c/Item
2).
Anl_GE_SA_1335_P_SPK7.indb 23 Anl_GE_SA_1335_P_SPK7.indb 23
GB
4. The safety lock-off is deactivated for as long
as you pull and hold the engine start/stop le-
ver (Fig. 9d).
5. Start the engine using the reversing starter
(Fig. 9e/Item 15). To do this, pull out the
handle by approx. 10-15cm (until you feel a
resistance) and then start the engine with a
sharp tug. If the engine does not start, tug the
handle again. Do not allow the handle to whip
back of its own accord.
6. Let the engine warm up in idle mode.
7. To stop the engine, simply release the engine
start/stop lever.
Important: When the engine start/stop lever is
released it must return to its initial position and
the engine must stop. If this is not the case, do not
use the equipment again.
Warning! The scarifi er roller begins to rotate as
soon as the engine is started.
Warning! Never open the ejector fl ap when the
motor is running. A rotating cutting unit can cause
injuries.
Always fasten the ejector fl ap carefully. The fl ap
fl ips back to the "Closed" position by the tension
springs!
Always ensure that a safe distance (provided
by the long handles) is maintained between the
user and the housing. Be especially careful when
scarifying and changing direction on slopes and
inclines. Maintain a solid footing and wear sturdy,
non-slip footwear and long trousers. Always sca-
rify along the incline (not up and down).
For safety reasons, the scarifi er may not be used
to scarify inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the scarifi er (tripping hazard)!
Adjusting the scarifi er depth (see Fig. 7)
The scarifi er depth is set with the adjustment me-
chanism. Pull the lever in the direction indicated
by the arrow (see Fig. 7) and adjust to the requi-
red position (0/ 1/ 2/ 3). Make sure that the lever
latches in place correctly!
0 = drive/transport position
1 = scarifi er depth 3 mm
2 = scarifi er depth 6 mm
3 = scarifi er depth 9 mm
Notice! For transport move the lever for setting
the depth to the highest position.
- 23 -
16.09.2016 09:36:21 16.09.2016 09:36:21