Standard Accessories - HIKOKI C 6SS Instrucciones De Manejo

English
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard moves smoothly and freely.
9. Never use the circular saw with its lower guard fi xed in
the open position.
10. Ensure that the retraction mechanism of the guard
system operates correctly.
11. Never operate the circular saw with the saw blade turned
upward or to the side.
12. Ensure that the material is free of foreign matters such as
nails.
13. For model C6SS, the saw blades range should be from
160 mm to 165 mm.
For model C7SS, the saw blades range should be from
185 mm to 190 mm.
14. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or maintenance.
15. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
16. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
17. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
18. Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
(Fig.1)
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
19. Should lever (A) remain loosened, it will create a very
hazardous situation. Always thoroughly clamp it. (Fig.2)
20. It is very hazardous to allow wing bolt to remain loosened.
Always thoroughly clamp it. (Fig.3)
21. Prior to cutting operation, make sure the material you
are going to cut. If the material to be cut is expected to
generate harmful / toxic dusts, make sure the dust bag
or appropriate dust extraction system is connected with
dust outlet tightly.
Wear the dust mask additionally, if available.
○ Before starting to saw, confi rm that the saw blade has
attained full-speed revolution.
○ Should the saw blade stop or make an abnormal
noise while operating, promptly turn OFF the switch.
○ Always take care in preventing the power cord from
coming near to the revolving saw blade.
○ Using the circular saw with the saw blade facing
upwards or sideways is very hazardous. Such
uncommon applications should be avoided.
○ When cutting materials, always wear protective
glasses.
○ When fi nished with a job, pull out the plug from the
receptacle.
22. After having attached the saw blade, reconfi rm that the
lock lever is fi rmly secured in the prescribed position.
23. Check that there are no nicks or scratches in the cord.
24. Check the exterior and ensure that there is no damage.
25. Use a saw blade with a displayed rotational speed equal
to or higher than the rotational speed of the tool.
26. Use a saw blade that suits each diff erent cutting material.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
C6SS / C7SS : Circular Saw
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
Always wear hearing protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
Cutting depth
P
Power Input
n
No-Load speed
0
Weight (without cord)*
kg
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool
* According to EPTA-Procedure 01/2014

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains
the accessories listed in the below.
○ Saw Blade (mounted on tool) ......................................1
(
Dia. 165 mm ................................ C6SS
Dia. 190 mm ................................ C7SS
○ Hex. Bar wrench .........................................................1
○ Dust collector .............................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
4
)