DeWalt DCF008 Manual De Instrucciones página 29

LED Light (Fig. A)
To turn the light on, push the slide switch located on the
3
underside of the screwdriver toward the front of the tool.
Drilling

WARNING: It is important to support work
properly and to hold the drill firmly to prevent loss
of control which could cause personal injury If you
have questions on how to operate tool, contact
an authorized service center or other qualified
service personnel.
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the
safety Instructions.
• Use appropriate and required safety equipment, as
instructed in the safety instructions.
• Secure and maintain work area, as instructed in the
safety instructions.
• Run the drill very slowly, using light pressure, until the
hole is started enough to keep the drill bit from slipping
out of it.
• Apply pressure in a straight line with the bit. Use
enough pressure to keep the bit biting but not so much
as to stall the motor or deflect the bit.
• Hold the tool firmly with two hands to control its
twisting action.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF
AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE
DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure
and slowly drilling through last part of hole.
• Keep the motor running while pulling the bit out of a
drilled hole This will help reduce jamming.
• Make sure switch turns drill on and off.
Drilling In Wood
Holes in wood can be made with the same twist drill bits
used for metal. These bits should be sharp and should be
pulled out frequently when drilling to clear chips from
the flutes.
NoTE: This tool is not recommended for drilling in metal
or masonry.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
or a D WALT authorized service center. Always use
e
identical replacement parts.
Protecting the Environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
spECIFICaTIoNs
DCF008 Charger specifications
aR B2/B2C
Voltage 220 V
Frequency 50 Hz 50/60 Hz
Input Current
Output Current
Output Voltage
Approximate
Charging Time
DCF008 8V screwdriver specifications
Voltage
ENglIsh
WALT
e
B3 BR
220 V 120 V 127 V
60 Hz 60 Hz
0.5 A
1.5 A
10.5 V
60 Min.
8V
27