Tabla de contenido
Publicidad
Manual del operario
Seguridad general
Señales de seguridad y ubicaciones
33952
DANGER
Counterweight downhill:
1Lower boom.
2Retract boom.
Tip-over Hazard
If tilt-alarm
sounds, unit is
on a severe
slope. Death or
Counterweight uphill:
serious injury
1Retract boom.
could occur.
2Lower boom.
33952 B
97890
DANGER
Improper Use Hazard
Do not alter or disable machine components that in any
way affect safety and stability.
The operator is responsible for safe machine
Do not push off or pull toward any
operation. This includes:
object outside of the platform.
1Avoid hazardous situations.
Do not place or attach overhanging
2Always perform a pre-operation inspection.
loads to any part of this machine.
3Always perform function tests prior to use.
Do not place ladders or scaffolds in
4Inspect work place.
platform or against any part of this
machine.
5Only use the machine as it was intended.
Do not use machine on a moving or mobile surface or
Do not operate unless:
vehicle.
You read, understand and obey:
Be sure all tires are in good condition, air-filled tires are
- manufacturer s instructions and safety rules
properly inflated and lug nuts are properly tightened.
safety and operator's manuals and decals
Fall Hazards
- employer s safety rules
- applicable governmental regulations
You are properly trained to safely operate this machine.
Electrocution Hazards
This machine is not electrically
insulated and willnot provide
protection from contact with or
proximity to electrical current.
Minimum Safe Approach Distance
Voltage
Distance
Phase to Phase
Feet Meters
0 to 300V
Avoid Contact
300V to 50KV
103.05
50KV to 200KV
154.60
Collision Hazards
200KV to 350KV206.10
350KV to 500KV257.62
Be aware of limited sight distance and blind spots when
500KV to 750KV
3510.67
driving or operating.
750KV to 1000KV
4513.72
Check work area for overhead
obstructions or other possible
Tip-over Hazards
hazards.
Do not raise or extend boom unless
Be aware of crushing hazard
machine is on firm, level ground.
when grasping the platform guard
rail.
Do not depend on tilt alarm as a
Observe and use color-coded
level indicator. Tilt alarm sounds in
direction arrows on the platform
platform only when machine is on a
controls and drive chassis for
severe slope.
drive and steer functions.
Do not raise boom when wind speeds
Do not lower the boom unless the area below is clear of
may exceed 28 mph / 12.5 m/s.
personnel and obstructions.
Do not operate machine in strong or
gusty winds. Do not increase surface
Explosion Hazard
area of platform or load. Increasing
Do not start engine if you smell or detect liquid
area exposed to wind will decrease
petroleum gas (LPG), gasoline, diesel fuel or other
machine stability.
explosive substances.
Do not drive machine on or near uneven terrain, unstable
Do not refuel the machine with the engine running.
surfaces or other hazardous conditions with boom raised
Damaged Machine Hazards
or extended.
Do not use a damaged or malfunctioning machine.
Do not drive machine on a slope that exceeds the
maximum slope or side slope rating for the machine.
Be sure all maintenance has been performed as
specified in the appropriate operator's and service
Use extreme care and slow speeds while driving the
manuals
machine in stowed position across uneven terrain,
debris, unstable or slippery surfaces and near holes
Be sure all decals are in place and legible.
and drop-offs.
Be sure safety, operator s and responsibilities manuals
are complete, legible and in the storage container
Do not attempt to free a caught or snagged platform
located on the platform.
using platform controls. All personnel must be removed
from platform before attempting to free platform using
ground controls.
82862
DANGER
Fire Hazard
Serious injury or death will
result if fire occurs while
operating welder and fire
extinguisher is not available.
Do not operate welder unless
fire extinguisher is immediately
available for instant use, per
OSHA regulation 1926.352(d).
82862 C
6
1000262
DANGER
Tip-over Hazard
Failure to match rated loads could result in an
overloaded platform, which could result in
machine tipping over.
When replacing platform, be
sure rated load on replacement
platform matches rated load on
machine serial number label.
Do not attach this platform to a
machine with any other rated
load.
Occupants must wear a safety
belt or harness in accordance
with governmental regulations.
Attach lanyard to anchor
provided in platform.
Do not sit, stand or climb on
the platform guard rails.
Maintain a firm footing on the
platform floor at all times.
Do not climb down from the
platform when raised.
Lower the platform entry mid-
rail or close the entry gate
before operating.
97890 A
28236
WARNING
Read and understand Operator's
Manual, Responsibilities Manual and
Safety Manual and all safety signs
before using or maintaining machine.
If you do not understand the
Improper operation or
information in the manuals, consult
maintenance can result in
your supervisor, the owner or the
serious injury or death.
manufacturer.
82237
DANGER
Electrocution
Hazard
Contact with
Avoid contact
energized
with energized
components can
components.
result in death or
serious injury.
82237 B
S-60 High Capacity
Primera edición • Segunda impresión
97579
DANGER
1250 lbs /
Tip-over Hazard
Do not overload
Welder power supply
platform.
reduces rated platform
1000262 B
Welder power supply
Capacity and must be
weighs 75 lbs / 34 kg.
Factored into total
platform load.
28236 D
750 lbs /
340 kg
567 kg
114269 A
N° de pieza 114303SP
33952
97890
1000262
28236
82862
97579
82237
97579
Publicidad
Tabla de contenido
