Tabla de contenido
Solución de problemas
Manuales relacionados para Westinghouse Aiden
Resumen de contenidos para Westinghouse Aiden
- Página 1 ETL-ES-Aiden-WH15 Owner's Manual Manual del usuariO Aiden Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: net weight: 17.27 lBs Peso neto: 7.85 KGs...
-
Página 2: Safety Tips
ETL-ES-Aiden-WH15 safety tiPs OBserVe tHe fOllOwinG: read and saVe tHese instruCtiOns warninG: tO reduCe tHe risK Of fire, eleCtriC sHOCK, Or PersOnal inJury, MOunt tO Outlet BOX MarKed 'aCCePtaBle fOr fan suPPOrt Of 35 lBs (15.9 KG) Or less' and use MOuntinG sCrews PrOVided witH tHe Outlet BOX and/Or suPPOrt direCtly frOM BuildinG struCture. -
Página 3: Consejos De Seguridad
ETL-ES-Aiden-WH15 COnseJOs de seGuridad HaGa lO siGuiente: lea y Guarde estas instruCCiOnes adVertenCia: Para reduCir el riesGO de inCendiO, desCarGa elÉCtriCa O Heridas GraVes PersOnales, MOnte en una CaJa de eMButir rOtulada “adeCuada Para VentiladOres de 35 lB (15,9 KG) O MenOs” utiliZandO lOs tOrnillOs de MOntaJe inCluidOs COn la CaJa de eMButir y/O MOnte direCtaMente en la estruCtura del edifiCiO. la MayOrÍa de las CaJas de eMButir utiliZadas nOrMalMente COn artefaCtOs de iluMinaCiÓn nO sOn adeCuadas Para VentiladOres y deBerÍan ser reeMPlaZadas. -
Página 4: Features Características
ETL-ES-Aiden-WH15 features CaraCterÍstiCas SLOPED CEILING DOWNROD INSTALLATION INSTALLATION FLUSH MOUNT INSTALLATION INSTALACIóN PARA INSTALACIóN CON INSTALACIóN AL TECHO VARILLA VERTICAL TECHO INCLINADOS For low ceilings For normal ceilings May require a longer downrod (sold separately) Para techo bajos Para techo normales Podría requerir una varilla vertical más larga... - Página 5 ETL-ES-Aiden-WH15 features CaraCterÍstiCas COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements your decor, or change the style with just a flip of the blade. NOTE: Combo-Blade finishes vary, depending upon model. ALETAS DE DOBLE CARA Las aletas del rotor de doble cara presentan dos superficies con un acabado de alta calidad.
-
Página 6: Preparing For Installation Antes De La Instalación
ETL-ES-Aiden-WH15 PreParinG fOr installatiOn antes de la instalaCiÓn Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble). -
Página 7: Mounting Bracket Installation Instalación Con Soporte De Montaje
ETL-ES-Aiden-WH15 MOuntinG BraCKet installatiOn instalaCiÓn COn sOPOrte de MOntaJe Remove the screws and star washers from the two mating holes (2) on the canopy. Loosen (do not remove) the screws in the mating slots (1) on the canopy. Rotate the mounting bracket and remove from the canopy. - Página 8 ETL-ES-Aiden-WH15 MOuntinG BraCKet installatiOn MOuntinG OPtiOns instalaCiÓn COn sOPOrte OPCiOnes de MOntaJe de MOntaJe Choose a MOuntinG OPtiOn elija una OPCiÓn de MOntaJe flusH MOunt OPtiOn If flush mount option is selected, proceed to page 9, step 6. OPCiÓn de instalaCiÓn al ras Si elige la opción de montaje al ras,...
- Página 9 ETL-ES-Aiden-WH15 flusH MOunt OPtiOn OPCiÓn de instalaCiÓn al ras For flush mount option, raise fan assembly and place onto hook (1) from mount- ing bracket into a closed hole on the canopy. This will allow for hands free wiring. Guide motor wires through the base of the canopy as shown and attach canopy PrOCeed direCtly tO PaGe 15 fOr wirinG OPtiOns.
- Página 10 ETL-ES-Aiden-WH15 nOrMal dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal Para teCHO nOrMal Place downrod assembly (1) into canopy (2) and coupling cover (3). Feed motor wires though the downrod assembly (1). Remove cotter pin (1) and cross pin (2) from downrod (3).
- Página 11 ETL-ES-Aiden-WH15 nOrMal dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal Para teCHO nOrMal Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling. Install cross pin (1) through coupling and downrod. Insert cotter pin (2) into cross pin until it snaps into place. Tighten set screws (3) in coupling. Slide coupling cover (4) over the downrod coupling. PrOCeed tO PaGe 14, steP 14.
- Página 12 ETL-ES-Aiden-WH15 eXtended dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal MÁs larGa Slide downrod ball (1) off of downrod and remove pin (2). Loosen (1) downrod ball from downrod (2) by removing set screw (3). Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical y Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando quite el pasador (2).
- Página 13 ETL-ES-Aiden-WH15 eXtended dOwnrOd OPtiOn OPCiÓn COn Varilla VertiCal MÁs larGa Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod. If no pre-drilled hole exists in the extended downrod, tighten the set screw against the downrod to secure the downrod ball.
- Página 14 ETL-ES-Aiden-WH15 MOuntinG MOntaJe Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the following Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
-
Página 15: Wiring Options
ETL-ES-Aiden-WH15 wirinG OPtiOns OPCiÓn de CaBleadO Pull CHain wirinG OPtiOn wall COntrOl wirinG OPtiOn *Connect blue wire only if attaching light kit with fan. Follow diagram above to make wiring connections for fan pull chain control. Follow diagram above to make wiring connections for wall control operation. -
Página 16: Secure To Ceiling Asegure El Ventilador Al Techo
ETL-ES-Aiden-WH15 Secure To ceiling ASegure el venTilAdor Al TecHo For flush mount fans, carefully lift fan up to the mounting bracket, making sure not to break any wire connections. For downrod fans, slide the canopy up to the mounting bracket. -
Página 17: Blade Installation Instalación De Las Aletas
ETL-ES-Aiden-WH15 Blade installatiOn instalaCiÓn de las aletas If plastic shipping stabilizer tabs are attached to motor, remove and discard (20a). Attach blade assembly to motor using the noise-dampening motor gaskets and motor screws provided. Tighten screws securely. NOTE: Some models do not utilize motor gaskets, washers, or stabilizer tabs. -
Página 18: Switch Housing Installation Instalación Del Alojamiento Del Interruptor
ETL-ES-Aiden-WH15 SWiTcH HouSing inSTAllATion inSTAlAción del AloJAMienTo del inTerruPTor Remove one of the screws (1) on the mounting plate (3), and loosen, (do not remove) the other three (2). Quite uno de los tornillos (1) del soporte de la placa del juego de luces (3) y suelte (sin quitar) los otros tres (2). - Página 19 ETL-ES-Aiden-WH15 SWiTcH HouSing inSTAllATion inSTAlAción del AloJAMienTo del inTerruPTor Insert the wires from motor going through the center hole of switch housing cap as Remove the 3 screws from switch housing cap, keep them for future usage. shown. alojamiento del interruptor Quítale los 3 tornillos de la tapa del...
- Página 20 ETL-ES-Aiden-WH15 SWiTcH HouSing inSTAllATion inSTAlAción del AloJAMienTo del inTerruPTor Attach the switch housing cap onto the mounting plate (1), by placing the key slot holes from the switch housing cap onto the three protruding screw heads from the mounting plate (1). Twist the switch housing cap clockwise until the screw heads engage the key slots.
- Página 21 ETL-ES-Aiden-WH15 SWiTcH HouSing inSTAllATion inSTAlAción del AloJAMienTo del inTerruPTor Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling. Confirm chains are held by lightly pull- Attach the switch housing onto the switch housing cap, align the holes from ing both chains in coupling.
-
Página 22: Operation And Maintenance
ETL-ES-Aiden-WH15 OPeratiOn and MaintenanCe Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. -
Página 23: Operación Y Mantenimiento
ETL-ES-Aiden-WH15 OPeraCiÓn y ManteniMientO Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc. -
Página 24: Troubleshooting Guide
ETL-ES-Aiden-WH15 If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these trOuBlesHOOtinG Guide installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself. -
Página 25: Guía Para Solucionar Problemas
ETL-ES-Aiden-WH15 Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos GuÍa Para sOluCiOnar PrOBleMas casos, estos errores de instalación podrían ser confundidos con defectos. Si experienca algun fallo, consulte esta guía para solucionar problemas. -
Página 26: Parts List Lista De Repuestos
ETL-ES-Aiden-WH15 Parts list lista de rePuestOs description 1 ..... . Mounting Bracket 2 ..... . Blade Bracket 3 . - Página 27 ETL-ES-Aiden-WH15...
- Página 28 ETL-ES-Aiden-WH15 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting All rights reserved. Made in China...