Specific Safety Rules - Porter & Cable PCE605 Manual De Instrucciones

d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments,
changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
g) Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
• Use clamps or another practical way
to secure and support the work piece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
• Disconnect power before using tool near
live wires or where there may be hidden
wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the
power tool "live" and could give the operator
an electric shock." Always check for hidden
wiring, gas lines, or other utilities before
performing any material cutting or removal
operations with the tool.
• Wait for the cutter to stop before setting
the tool down. An exposed cutter may
engage the surface leading to possible loss
of control and serious injury.
• Do not operate this tool for long periods
of time. Vibration caused by the operating
action of this tool may cause permanent
injury to fingers, hands, and arms. Use
gloves to provide extra cushion, take
frequent rest periods, and limit daily time of
use.
• Always hold the tool firmly with both
hands for maximum control. Keep proper
footing and balance at all times. This enables
better control of the power tool in unexpected
situations.
• Do not restart the cutting operation in the
work piece. Let the tool reach full speed and
carefully re-enter the cut.
• Do not "jam" the cut-off saw blade or
apply excessive pressure. Do not attempt
to make an excessive depth of cut.
• Keep your hands away from cutting area.
Do not reach under the material being cut.
• Do not use dull or damaged blades. Bent
blade can break easily or cause kickback.
Exercise extreme caution when handling the
accessories. The accessories are very sharp.
Wear protective gloves when changing
cutting accessories. Accessories become
3