Ice Maker And Storage Bin - Sears KENMORE ELITE 106.4116 Serie Manual De Uso

Water Filter Status Light
The water filter status light will help you know when to change
your water filter.
When the dispenser control panel's water filter status
display changes to "ORDER," this tells you that it is almost
time to change the water filter cartridge.
Replace the water filter cartridge when the water filter
status display changes to "REPLACE."
NOTE: If water flow to your water dispenser or ice maker
decreases noticeably, change the filter sooner. The filter
should be replaced at least every 6 months, depending on
your water quality and usage.
You can check the remaining life of your water filter at any time.
Press SETTINGS, then press SETTINGS again. The display
screen will show how many more gallons of water the filter
can effectively filter. Press WATER/ICE to exit the filter
status screen.
NOTE: A new filter's "Gallons Remaining" display is 200.
The "ORDER" status begins at 40 gal. (151 L) remaining, and
the "REPLACE" status activates when the filter has 0 gal.
remaining.
Resetting the Filter Status
After changing the water filter, reset the status light. Press
and hold TEMPERATURE and SETTINGS at the same time
for 3 seconds.
IMPORTANT: To avoid unintentionally changing other
settings, be sure to press both buttons at exactly the same
time.
When the system is reset, the "ORDER" and "REPLACE"
icons will disappear from the display screen.
NOTE: When the status displays "REPLACE," you can
temporarily reset the status icon manually, without changing the
water filter. Press and hold the ACCENT LIGHT and
TEMPERATURE buttons at the same time for 3 seconds. The
"REPLACE" display will be turned off for 14 days. When it turns
back on, you can manually reset it again if desired.
Changing the Water Filter
1. Locate the water filter in the top-right corner of the
refrigerator compartment.
2. Lift open the filter cover door. The filter will be released and
then be ejected as the door is opened.
3. When the door is completely open, pull the filter straight
out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
4. Take the new filter out of its packaging and remove the cap.
Be sure the O-rings are still in place after the cap is
removed.
B
A B
A. Cap
5. With the arrow pointing up, align the new filter with the
filter housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the
filter into place. You may need to press hard.
7. Flush the water system. See "Water and Ice Dispensers."

Ice Maker and Storage Bin

Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply
cannot be avoided, make sure the water softener is
operating properly and is well maintained.
Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the
dispenser mechanism.
Do not store anything on top of or in the ice maker or
storage bin.
Turning the Ice Maker On/Off
The On/Off switch can only be accessed when the ice storage
bin has been removed. The switch is located on the freezer door,
on the left side of the wall that surrounds the ice storage bin.
See the following section for bin removal instructions.
To turn on the ice maker, slide the control to the ON (left)
position.
To manually turn off the ice maker, slide the control to the
OFF (right) position.
NOTE: The ice maker has an automatic shutoff to keep the
storage bin from overfilling during normal operation. The ice
maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position.
B. O-rings
13