Tool Change - stayer SCC255 Manual De Instrucciones

6. Limitations regarding environmental conditions
7. List of contents
8. Settings and testing
9. Changing tools
10. Fixing for operation
11. Limits regarding the workpiece size
12. General instructions for use
13. Dust extraction
14. Regular cleaning, maintenance and greasing.
15. Warrantee.
16. Disposal.
17. Technical specifications
18. Declaration of conformity
8. Settings and testing
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense
use, it must be checked and adjusted so as to ensure the
machine's correct quality of service and safety.
This requires knowledge, experience and special tools.
The official technical service of Stayer Iberica S.A. will ca-
rry out that work for you in a quick thorough and inexpen-
sive manner.
Adjusting the locking in the lower resting position
Verification
1. Levantar el cabezal apretando el botón 3.
2. Lower the head until reaching the stop.
3. Press button 5. If it is well adjusted, the bolt of the bu-
tton should smoothly enter up to the stop. If not, proceed
to adjust it.
Adjustment
1. Loosen the fastening screw of the locking screw 6.
2. Lower the head to the lower stop.
3. Tighten or loosen screw 6 until the knob 5 penetrates
the stop smoothly.
4. While the screw is held, tighten the nut of the perpen-
dicular restraint.
Adjust the angle of the horizontal mitre joint to
+- 45º
Verification
1. Move the head horizontally until it is locked at +45º.
2. Verify that the horizontal angle indicator marks exactly
45º. If not, proceed to the adjustment.
3. Repeat the same sequence for the horizontal angle at
-45º.
Adjustment
1. Move the head set and the cutting table horizontally
until it locks at 45º.
2. Work on the screws 9 until obtaining exactly 45º.
3. Repeat the same sequence for the horizontal angle at
-45º.
ENGLISH
11
Adjust the vertical mitre joint angle to 90º and
45º.
Verification
1. Release the vertical adjustment of the head by loose-
ning 8.
2. Move the head to the right stop (90º) or left stop (45º).
3. Check the angle by means of a duly calibrated angular
template or a compass (minimum precision +-5') presen-
ting one of its surfaces on the lower table and the other
on the cutting disc. Use light as contrast to see the ad-
justment.
4. If the face of the template does not adjust exactly with
the disc or if the direct measurement of the compass
shows a deviation greater than +- 20', proceed to the ad-
justment.
Adjustment
1. Work on the adjustment screws 7 until reaching a mea-
surement of 90º or 45º.
Adjust the separator blade
It is black metallic plate that is behind the upper part of the
disc. Its function is to impede the joining of the pieces that
are being cut and flying out towards the user's face.
In order to verify and adjust, access the blade, performing
step 1 of the section 'Change cutting disc' and verify the
alignment of the blade with the disc and that the distance
between the teeth of the disc and the blade surface is 2
mm. If it is not, adjust with the two screws that hold the
blade.

9. Tool change

Warning!
Before any intervention in the electric tool, remove the
plug from the outlet.
Warning!
It is mandatory to use discs according to EN 847-1 STA-
YER originals.
Change of cutting disc
1. Remove the upper table. To do this, remove the support
screws of the upper aluminium table, the three crosshead
screws of the upper black safeguard and the screw of the
interior rocker arm of the safeguard.
2. Hold the cutting disc with a piece of wood against its
teeth and loosen the screw rotating it to the right.
3. Extract the disc from above and install the new one fo-
llowing the two previous sections in reverse order.
11