Levantar El Cabezal Apretando El Botón; Tool Change; Cambio Del Disco De Corte - stayer SCR315W Manual De Instrucciones

7. List of contents
1. Provided uses of the machine
2. Unpackaging and assembling
3. Setting or fastening the machine in a stable position
4. Connection to the grid, wiring, fuses, socket type for the
jack and grounding conditions
5. Illustrated descriptions of functions
6. Limitations regarding environmental conditions
7. List of contents
8. Settings and testing
9. Changing tools
10. Fixing for operation
11. Limits regarding the workpiece size
12. General instructions for use
13. Dust extraction
14. Regular cleaning, maintenance and greasing.
15. Warrantee.
16. Disposal.
17. Technical specifications
18. Declaration of conformity
8. Settings and testing
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense
use, it must be checked and adjusted so as to ensure the
machine's correct quality of service and safety.
This requires knowledge, experience and special tools.
The official technical service of Stayer Iberica S.A. will ca-
rry out that work for you in a quick thorough and inexpen-
sive manner.
Adjusting the locking in the lower resting position
Verification
1. Levantar el cabezal apretando el botón 2.
2. Bajar el cabezal hasta hacer tope.
3. Press button 5. If it is well adjusted, the bolt of the bu-
tton should smoothly enter up to the stop. If not, proceed
to adjust it.
Adjustment
1. Loosen the fastening screw of the locking screw 6.
2. Lower the head to the lower stop.
3. Tighten or loosen screw 6 until the knob 5 penetrates
the stop smoothly.
4. While the screw is held, tighten the nut of the perpen-
dicular restraint.
Adjust the angle of the horizontal mitre joint to
+- 45º
Verification
1. Move the head horizontally until it is locked at +45º.
2. Verify that the horizontal angle indicator marks exactly
45º. If not, proceed to the adjustment.
3. Repeat the same sequence for the horizontal angle at
-45º.
ENGLISH
10
Adjustment
1. Move the head set and the cutting table horizontally
until it locks at 45º.
2. Work on the screws 7 until obtaining exactly 45º.
3. Repeat the same sequence for the horizontal angle at
-45º.
Adjust the vertical mitre joint angle to 90º and 45º.
Verification
1. Release the vertical adjustment of the head by loose-
ning 8.
2. Move the head to the right stop (90º) or left stop (45º).
3. Check the angle by means of a duly calibrated angular
template or a compass (minimum precision +-5') presen-
ting one of its surfaces on the lower table and the other
on the cutting disc. Use light as contrast to see the ad-
justment.
4. If the face of the template does not adjust exactly with
the disc or if the direct measurement of the compass
shows a deviation greater than +- 20', proceed to the ad-
justment.
Adjustment
1. Work on the adjustment screws 7 until reaching a mea-
surement of 90º or 45º.

9. Tool change

Warning!
Before any intervention in the electric tool, remove the
plug from the outlet.
Warning!
It is mandatory to use discs according to EN 847-1 STAYER
originals.

Cambio del disco de corte

1. Lift the disc guard.
2. Hold the disc by pressing 3 and loosen the disc screw
spinning it to the right.
3. Extract the disc from above and install the new one fo-
llowing the two previous sections in reverse order.
10. Fixing for operation
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene. During the cut,
keep the workpiece fixed to the support.
While cutting the piece must be steadily held.
MANDATORY CLAMP USE.
To avoid deformations of the workpieces during fixing the-
reof, the use of wooden profiles being easily applicable to
the movable jaws of the clamps is advised. Clamps can
be easily extracted and leave the working surface totally
clear
Clamps can be installed on 11.
For cutting long workpieces under safe conditions it is es-
sential to hold them with additional supports located in the
10, once placed fix them with the screws under the table.
10