Briggs & Stratton 80000 Manual Del Operario página 9

How To Clean The Air Cooling System - Figure 14
WARNING
Running engines produce heat. Engine parts, especially muffler,
become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.

Remove accumulated debris from muffler area and cylinder area.

NOTICE: Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
Use a brush or dry cloth to remove debris from the finger guard (A). Keep linkage,
springs and controls (B) clean. Keep the area around and behind the muffler (C) free of
any combustible debris (Figure 14).
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum
deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton Advanced Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel
system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil.
NOTICE: Store the engine level (normal operating position). If the engine is tipped for
storage, the fuel tank must be empty and the spark plug side must be up. If the fuel
tank is not empty and if the engine is tipped in any other direction, it may be difficult to
start due to oil or gasoline contaminating the air filter and/or the spark plug.
Troubleshooting
Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in
USA).
en
Specifications
Engine Specifications
Model
Displacement
Bore
Stroke
Oil Capacity
Engine Specifications
Model
Displacement
Bore
Stroke
Oil Capacity
Engine Specifications
Model
Displacement
Bore
Stroke
Oil Capacity
Tune-up Specifications *
Model
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10 F (5.6 C) above 77 F (25 C). The engine will operate satisfactorily at
an angle up to 15. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Common Service Parts n
Service Part
Air Filter, Standard
Air Filter, High Capacity
Oil -- SAE 30
Advanced Formula Fuel Treatment & Stabilizer
Resistor Spark Plug
Spark Plug Wrench
Spark Tester
n We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
80000
7.63 ci (125 cc)
2.362 in (60 mm)
1.750 in (44.45 mm)
15 oz (0.44 L)
90000
8.64 ci ( 140 cc)
2.495 in (63.40 mm)
1.750 in (44.45 mm)
15 oz (0.44 L)
093J00
9.15 ci ( 150 cc)
2.583 in (65.60 mm)
1.750 in (44.45 mm)
15 oz (0.44 L)
80000, 90000, 093J00
0.020 in (0.51 mm)
180 lb-in (20 Nm)
0.006 - 0.014 in (0.15 - 0.36 mm)
0.004 - 0.008 in (0.10 - 0.20 mm)
0.004 - 0.008 in (0.10 - 0.20 mm)
Part Number
799579
798452
100113
5442
692051
19576
19368
9