Standard Accessories - HIKOKI G 10SN2 Instrucciones De Manejo

Ocultar thumbs Ver también para G 10SN2:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 31
8. When the machine is not use, the power source should
be disconnected.
9. Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident
before the depressed center wheel is assembling and
disassembling.
10. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
11. Do not operate from a direct current power source,
booster or any other type of transformer. Doing so may
not only cause damage to the grinder, but may lead to
accidents.
12. Some mobile generators may not be usable with the
machine.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
G10SN2 / G12SN2 / G13SN2
G10SN2(S) / G12SN2(S) / G13SN2(S):
Disc Grinder
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
Alternating current
Power input
P
n
Rated speed
min
Revolution or reciprocations per minute
-1
D
Wheel outer diameter
d
Wheel hole diameter
t
Wheel thickness
Peripheral speed
Weight
(According to EPTA-Procedure 01/2003)
kg
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Warning
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
(1) Wrench .........................................................................1
(2) Side handle ...................................................................1
(3) Depressed center wheel ...............................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Cutting of synthetic concrete, stone, brick, marble, and
similar materials.
SPECIFICATIONS
The specifi cations of this machine are listed in the Table on
page 133.
○ Soft-start (only G10SN2(S), G12SN2(S), G13SN2(S))
○ 0 Voltage Re-start Protection (only G10SN2(S),
G12SN2(S), G13SN2(S))
The 0 voltage restart protection feature prevents the
power tool from restarting after the power has been
temporarily cut off during operation.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Fitting and adjusting the wheel guard
Fixing the side handle
Assembling depressed center wheel
Assembling cutting wheel and wheel
guard*
1
Assembling diamond wheel and
wheel guard*
1
Switch operation*
2
Grinding angle and grinding method
Selecting accessories
*1 Optional
*2 When the 0 voltage re-start protection feature has been
activated, return the power switch to the OFF position
and wait for 1 second or more before restarting the
power tool. (Only G10SN2(S), G12SN2(S), G13SN2(S))
5
English
Figure
Page
1
134
2
134
3
135
4
135
5
135
6
135
7
136
137

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

G 12sn2G 13sn2G 10sn2(s)G 12sn2(s)G 13sn2(s)

Tabla de contenido