Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS USING PLUG-IN CORD
1.
Hold the fixture in the desired mounting location, leaving approximately 2 ½"
clearance for plug-in cord, and not more than 5' from the nearest outlet. Drive
mounting screws into cabinet surface until fixture is secure. If screws are
difficult to install, mark holes and drill 1/16" maximum pilot holes. (ref. FIG. 5)
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the
fixture.
2.
Connect cord into fixture female connector.
CAUTION: Never connect the plug-in cord to a fixture or system that is
already energized
3.
Peel backing off retaining clip(s) and affix to desired location(s). Surface should
be as clean as possible.
4.
Slip cables into clip(s) and snap closed.
5.
Open glass diffuser by pressing on tab of each diffuser end cap. Lift and slide
diffuser towards rear of fixture. Remove protective sleeve(s) from bulb(s).
INSTALLATION INSTRUCTIONS USING INTERCONNECT CABLE
1.
Turn off power.
2.
Hold the fixture in the desired mounting location, not more than 21" from
nearest interconnected fixture, allowing approximately 2 ½" clearance for
interconnect cables. Drive mounting screws into cabinet surface until fixture
is secure. If screws are difficult to install, mark holes and drill 1/16" maximum
pilot holes. (ref. FIG. 6)
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the fixture.
3.
Connect fixture to existing Kichler Cabinet Lighting system using interconnect
cable.
4.
Hold interconnect cable to mounting surface and determine best path for
cable. If interconnect cable is being run from cabinet to cabinet a notch such
as a "V" could be cut in cabinet side panels to help keep cables out of site.
NOTE: Interconnect cable is not intended for use through or concealed
behind walls, floors or ceilings.
5.
Peel backing off retaining clip(s) and affix to desired location(s). Surface should
be as clean as possible.
6.
Slip cables into clip(s) and snap closed.
INSTALLING FIXTURE TO FIXTURE
1.
Turn off power.
2.
Align connector on end of new fixture with connector on end of existing fixture.
(ref. FIG. 7)
3.
Push new fixture to existing fixture until fixtures are flush and connectors
snap together.
4.
Drive mounting screws into cabinet surface until fixture is secure. If screws
are difficult to install, mark holes, remove fixture and drill 1/16" maximum pilot
holes.
NOTE: For 22" and 30" fixtures, open wire compartment by inserting flathead
screwdriver into the slots and wedging cover open to install center screw.
Once installed, swing the cover towards the fixture and close it by pressing at
the ends of the cover until the cover snaps into place and is flush with the
fixture.
5.
Open glass diffuser by pressing on tab of each diffuser end cap. Lift and slide
diffuser towards rear of fixture. Remove protective sleeve(s) from bulb(s).
6.
Close glass diffuser by swinging edge with tabs up towards fixtures until pegs
by tabs slip into slots at the front of the fixture end caps. Slide tabs forward,
allowing pegs to seat in slots. Lens should be level and flush with fixture.
7.
If this will be an end fixture in a run, use connector cover over any connector
not being used.
8.
Turn on power.
INSTALLING REPLACEMENT LAMPS
1.
Turn off fixture and allow to completely cool before replacing lamp.
2.
Open glass diffuser by pressing on tab of each diffuser end cap. Lift and slide
diffuser towards rear of fixture.
3.
Remove lamp by pulling straight out from the lamp socket.
4.
Reference lamp mounting bracket for replacement lamp information. Use only
maximum 120V, 20W Xenon lamp.
5.
Close glass diffuser by swinging edge with tabs up towards fixtures until pegs
by tabs slip into slots at the front of the fixture end caps. Slide tabs forward,
allowing pegs to seat in slots. Lens should be level and flush with fixture.
See Page 1 for:
• Installation Instructions using Line Connection
Date Issued: 12/4/15
6.
Close glass diffuser by swinging edge with tabs up towards fixtures until pegs by
tabs slip into slots at the front of the fixture end caps. Slide tabs forward, allowing
pegs to seat in slots. Lens should be level and flush with fixture.
7.
If this will be an end fixture in a run, use connector cover over any connector not
being used.
8.
Plug cord into outlet.
FIG. 5
7.
Open glass diffuser by pressing on tab of each diffuser end cap. Lift and slide
diffuser towards rear of fixture. Remove protective sleeve(s) from bulb(s).
8.
Close glass diffuser by swinging edge with tabs up towards fixtures until pegs by
tabs slip into slots at the front of the fixture end caps. Slide tabs forward, allowing
pegs to seat in slots. Lens should be level and flush with fixture.
9.
If this will be an end fixture in a run, use connector cover over any connector not
being used.
10. Turn on power.
FIG. 6
FIG. 7
866-558-5706
We're here to help
Hrs: M-F 9am to 5pm EST
IS-4U120X-CB_English
Page 2
Publicidad
Tabla de contenido
