Shut Down; Enable Menu List; Patient Messages; Reminders - DeVilbiss Healthcare DV57 AUTOBILEVEL PAP Serie Guía De Instrucciones

pressure will start at the delay pressure and gradually rise to the prescription setting. In AutoBilevel mode, the IPAP and
EPAP pressures will gradually rise together until EPAP reaches the Min EPAP prescription settings.

Shut Down

Press the ON/OFF button to turn the device off. You may also simply remove your mask. After a few seconds the device
will display the message "Mask Off. Please check mask fi t." If you do not put the mask on again the device will
automatically turn off in about 20 seconds. Pressing any button will remove the message from the display.
NOTE–If the DeVilbiss IntelliPAP does not turn off automatically, the Auto-OFF feature may have been disabled. In this
case you must manually turn the device off.

Enable Menu List

The Enable menu is available in all modes and is a sub-menu that allows you to control various functions of your IntelliPAP.
It is accessed by pressing the down button while "Enable Menu" is shown on the Display.
Display Example
Auto-OFF
Enabled
Auto-ON
Enabled
Mask Fit Check
Enabled
Low Backlight
Enabled
Exit Menu
Press 

PATIENT MESSAGES

Your IntelliPAP will alert you of issues that may require some action on your part in order to make your therapy more
effective. You can press any key or button to clear the message from the display, but the IntelliPAP will operate normally
even if the message is not cleared. Two kinds of messages are displayed: Reminders and Notifi cations.

Reminders

Reminders alert you when parts of your system need to be replaced. Some components of your system wear over time
and, if not replaced, may compromise your therapy. If you see a message on the display that is not listed below, you may
have the optional DeVilbiss SmartLink Module attached to your device (Fig. F), which provides additional messages. Refer
to the documentation that was provided with the SmartLink Module.
Clean Filter – The fi lter should be checked every 10 days for signs of dirt or wear so that it can be cleaned as needed.
This message helps to remind you to check it regularly.

Notifications

Notifi cations identify conditions in your IntelliPAP that may require action by you or your equipment provider in order to
maintain a high level of therapy. If you see a message on the display that is not listed below, you may have the optional
DeVilbiss SmartLink Module attached to your device (Fig. F), which provides additional messages. Refer to the
documentation that was provided with the SmartLink Module.
Delay Running xx Minutes Left – While a comfort delay session is active, this message is fl ashed on the display every 5
seconds to let you know how much time is left in the delay.
Mask Leak – This message means the IntelliPAP has detected a large amount of airfl ow during therapy for at least 10% of
the time during your previous use session. This notifi cation is displayed when the device is turned on. If this message is
A-DV57
Enable Menu Item Description
This option controls the Auto-OFF feature, which automatically stops the fl ow of air

after taking off the mask. The device will require at least 30 seconds to turn OFF
depending on the kind of mask used. When Auto-OFF is enabled, Auto-ON is also
enabled. If the unlocked symbol is shown, you are able to adjust this setting. If the
locked symbol is shown, this setting can only be adjusted by your provider.
This option controls the Auto-ON feature, which automatically starts the fl ow of air

after breathing once or twice into the mask. This is always enabled when Auto-OFF is
enabled. If the unlocked symbol is shown, you are able to adjust this setting. If the
locked symbol is shown, this setting can only be adjusted by your provider.
This option controls the mask fi t check feature. The air fl ow to your mask is
constantly measured and if the amount of airfl ow exceeds 95 liters/minute for more
than 10% of the time used, a notifi cation will be created. This notifi cation will be
displayed the next time you use the IntelliPAP.
Low backlight Enable will keep the backlight dim during operation. Low backlight
Disabled will turn the backlight OFF during operation.
Pressing the up key exits the Enable menu.
EN - 9