Technical Data - AEG FS 280 Manual Original

tEchNIcal Data

FS 280
Rated input .................................................................................500 W
No-load speed ..............................................................6000 - 11000 min
Orbital travel diameter ..................................................................2,5 mm
Dimensions of grinding plate ............................................ 226 x 114 mm
Weight without cable ...................................................................3,0 kg
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ...........................................................81,5 dB(A)
Sound power level (K = 3 dB(A)) ...............................................................92,5 dB(A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according
to EN 60745.
Vibration emission value a ...................................................................................5,7 m/s
h
Uncertainty K= .....................................................................................................1,5 m/s
WARNING!
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment
of exposure.
The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SaFEty INStRuctIoNS
Wear ear protectors. Exposure to noise can cause hearing loss.
Appliances used at many different locations including open air should be
connected via a residual current device of 30 mA or less.
Always wear goggles when using the machine. It is recommended to wear
gloves, sturdy non slipping shoes and apron.
Always disconnect the plug from the socket before carrying out any work
on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always lead the
cable away behind you.
Before use check machine, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised Service Agents.
The dust produced when using this tool may be harmful to health (e.g. when
working oak or beech wood, stones, paint, which could contain lead or other
harmful chemicals). Do not inhale the dust. Use a dust absorption system and
wear a suitable dust protection mask. Remove deposited dust thoroughly, e.g.
with a vacuum cleaner.
Do not use machines on any material containing asbestos.
This machine is suitable only for dry sanding.
oscillating sander
The oscillating sander can be used for sanding wood, plastics and metal.
Do not use this product in any other way as stated for normal use.
-1
We declare under our sole responsibility that this product is in conformity
with the following standards or standardized documents: EN 60745, EN
55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, in accordance with
the regulations 2006/42/EC, 2004/108/EC
Winnenden, 2011-01-17
2
2
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SPEcIFIED coNDItIoNS oF uSE
Ec-DEclaRatIoN oF coNFoRmIty
Authorized to compile the technical file
maINS coNNEctIoN
Connect only to single-phase AC current and only to the system
maINtENaNcE
SymBolS
Please read the instructions carefully before starting the
machine.
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying
out any work on the machine.
Accessory - Not included in standard equipment, available
as an accessory.
Do not dispose of electric tools together with household
waste material! In observance of European Directive
2002/96/EC on waste electrical and electronic equipment
and its implementation in accordance with national law,
electric tools that have reached the end of their life must
be collected separately and returned to an environmentally
compatible recycling facility.
Rainer Kumpf
Manager Product Development
English
5
GB