Black and Decker KA160 Manual De Instrucciones página 8

Ocultar thumbs Ver también para KA160:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
ENGLISH
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust extraction connector
3. Base
4. Tip holder
5. Sanding base tip
6. Finger attachment
7. Profile attachment
8. Screw
9. Sanding profiles
In addition, this tool is supplied with some or all of the
following accessories:
Accessory
Coarse grit sandpaper
u
Medium grit sandpaper
u
Fine grit sandpaper
u
Extra fine grit sandpaper Sanding between coats
u
Detail sanding tips
u
1 OT polishing/stripping Polishing metals, stripping
u
wool
Grey foam pad
u
Red non-woven pad
u
Grey abrasive paper
u
Contour attachments
u
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
8
Recommended application
and use
Fast paint, varnish and rust
removal
Paint, varnish and rust removal
Surface blending and finishing
Corners and hard to reach places
varnish and glass cleaning
Applying and removing polish
Heavy scrubbing and rust
removal
Polishing plastics
Curves and profiles
Fitting sanding sheets (fig. A & B)
Detach the two diamond-shaped tips (10) from the
u
sanding sheet (11).
Hold the tool with the sanding base facing upwards.
u
Place the sanding sheet (11) onto the sanding base,
u
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (10) can be reversed and replaced
when worn.
When the front part of the tip is worn, detach it from the
u
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding
u
base and fit a new tip.
The polishing foam and pads (14) can be fitted the same
u
way as the sanding sheets.
Tip of the sanding base (fig. C)
When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
Black & Decker dealer.
Remove the screw (8).
u
Reverse or replace the worn part.
u
Fit and tighten the screw.
u
Finger attachment (fig. D)
The finger attachment is used for fine detail sanding.
Remove the screw (8).
u
Remove the diamond-shaped tip holder (4) from the
u
sanding base.
Fit the finger attachment (6) onto the sanding base.
u
Fit and tighten the screw.
u
Fit the appropiate sanding sheet (12) onto the finger
u
attachment.
Profile attachment (KA160K/KA161K only) (fig. E)
The profile attachment is used for contour sanding.
Remove the screw (8).
u
Remove the diamond-shaped tip holder (4) from the
u
sanding base.
Fit the profile attachment (7) onto the sanding base.
u
Fit and tighten the screw.
u
Fitting and removing a sanding profile (fig. F1 & F2)
Choose the sanding profile most suitable for your application.
u
Place one end of the sanding profile (9) into the recess at
u
the front end of the profile holder (7).
Push the other end of the sanding profile until it clicks into
u
place.
To remove the sanding profile, push it forward and pull the
u
rear end out of the profile holder (fig. F2).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ka160kKa161

Tabla de contenido