Important Safety Instructions - Canon imageCLASS D1650 Introducción

Appendix
Important Safety
Instructions
This chapter describes important safety
instructions for the prevention of injury to users
of this machine and others, and damage to
property. Read this chapter before using the
machine, and follow the instructions to use the
machine properly. Do not perform any
operations not described in this manual. Canon
will not be responsible for any damages resulting
from operations not described in this manual,
improper use, or repair or changes not
performed by Canon or a third party authorized
by Canon. Improper operation or use of this
machine could result in personal injury and/or
damage requiring extensive repair that may not
be covered under your Limited Warranty.
WARNING
Indicates a warning concerning operations
that may lead to death or injury to persons if
not performed correctly. To use the machine
safely, always pay attention to these warnings.
CAUTION
Indicates a caution concerning operations
that may lead to injury to persons if not
performed correctly. To use the machine
safely, always pay attention to these cautions.
IMPORTANT
Indicates operational requirements and
restrictions. Be sure to read these items
carefully to operate the machine correctly and
avoid damage to the machine or property.
Installation
To use this machine safely and comfortably,
carefully read the following precautions and
install the machine in an appropriate location.
WARNING
Do not install in a location that may result in a
fire or electrical shock
A location where the ventilation slots are
•
blocked (too close to walls, beds, sofas, rugs, or
similar objects)
A damp or dusty location
•
A location exposed to direct sunlight or
•
outdoors
• A location subject to high temperatures
A location exposed to open flames
•
Near alcohol, paint thinners or other
•
flammable substances
Other warnings
En
Do not connect unapproved cables to this
•
machine. Doing so may result in a fire or
electrical shock.
• Do not place necklaces and other metal
objects or containers filled with liquid on the
machine. If foreign substances come in
contact with electrical parts inside the
machine, it may result in a fire or electrical
shock.
When installing and removing the optional
•
accessories, be sure to turn OFF the power,
unplug the power plug, and then disconnect
all the interface cables and power cord from
the machine. Otherwise, the power cord or
interface cables may be damaged, resulting in
a fire or electrical shock.
If any foreign substance falls into this machine,
•
unplug the power plug from the AC power
outlet and contact your local authorized
Canon dealer.
30
CAUTION
Do not install in the following locations
The machine may drop or fall, resulting in injury.
• An unstable location
• A location exposed to vibrations
Other cautions
When carrying this machine, follow the
•
instructions in this manual. If carried
improperly, it may fall, resulting in injury.
When installing this machine, be careful not to
•
get your hands caught between the machine
and the floor or walls. Doing so may result in
injury.
Leveling feet (only for products with leveling
feet)
Do not remove the machine's leveling feet after
the machine has been installed, as this may
cause the machine to fall or tip over, resulting in
personal injury.
IMPORTANT
Do not install in the following locations
Doing so may result in damage to the
machine.
A location subject to temperature and
•
humidity extremes, whether low or high
• A location subject to dramatic changes in
temperature or humidity
A location near equipment that generates
•
magnetic or electromagnetic waves
• A laboratory or location where chemical
reactions occur
A location exposed to corrosive or toxic gases
•
• A location that may warp from the weight of
the machine or where the machine is liable to
sink (a carpet, etc.)
Avoid poorly ventilated locations
This machine generates a slight amount of ozone
and other emissions during normal use. These
emissions are not harmful to health. However,
they may be noticeable during extended use or
long production runs in poorly ventilated rooms.
To maintain a comfortable working environment,
it is recommended that the room where the
machine operates be appropriately ventilated.
Also avoid locations where people would be
exposed to emissions from the machine.
Do not install in a location where
condensation occurs
Water droplets (condensation) may form inside
the machine when the room where the machine
is installed is heated rapidly, and when the
machine is moved from a cool or dry location to
a hot or humid location. Using the machine
under these conditions may result in paper jams,
poor print quality, or damage to the machine.
Let the machine adjust to the ambient
temperature and humidity for at least 2 hours
before use.
In altitudes of above sea level 3,000 m or
higher
Machines with a hard disk may not operate
properly when used at high altitudes of about
3,000 meters above sea level, or higher.
Connecting the Telephone Line (Only for
Products with a Fax Function)
This machine conforms to a analog telephone
line standard. The machine can be connected to
the public switched telephone network (PSTN)
only. If you connect the machine to a digital
telephone line or a dedicated telephone line, it
might impede proper operation of the machine
and could be the cause of damage. Make sure to
confirm a type of telephone line before
connecting the machine. Contact your optical
fiber line or IP telephone line service providers if
you want to connect the machine to those
telephone lines.
When using wireless LAN (only for products
with a wireless LAN function)
• Install the machine at a distance of 50 meters
or less from the wireless LAN router.
As far as possible, install in a location where
•
communication is not blocked by intervening
objects. The signal may be degraded when
passing through walls or floors.
Keep the machine as far as possible from
•
digital cordless phones, microwave ovens, or
other equipment that emits radio waves.
Do not use near medical equipment. Radio
•
waves emitted from this machine may
interfere with medical equipment, which may
result in malfunctions and accidents.
If the operating noise concerns you
Depending on the use environment and
operating mode, if the operating noise is of
concern, it is recommended that the machine be
installed in a place other than the office.
Power Supply
WARNING
Use only a power supply that meets the
•
specified voltage requirements. Failure to do
so may result in a fire or electrical shock.
The machine must be connected to a
•
socket-outlet with grounding connection by
the provided power cord.
Do not use power cords other than the one
•
provided, as this may result in a fire or electrical
shock.
• The provided power cord is intended for use
with this machine. Do not connect the power
cord to other devices.
• Do not modify, pull, forcibly bend, or perform
any other act that may damage the power
cord. Do not place heavy objects on the power
cord. Damaging the power cord may result in
a fire or electrical shock.
Do not plug in or unplug the power plug with
•
wet hands, as this may result in an electrical
shock.
• Do not use extension cords or multi-plug
power strips with the machine. Doing so may
result in a fire or electrical shock.
• Do not wrap the power cord or tie it in a knot,
as this may result in a fire or electrical shock.
Insert the power plug completely into the AC
•
power outlet. Failure to do so may result in a
fire or electrical shock.
Remove the power plug completely from the
•
AC power outlet during a thunder storm.
Failure to do so may result in a fire, electrical
shock, or damage to the machine.
Make sure that the power supply for the
•
machine is safe, and has a steady voltage.
• Keep the power cord away from a heat source;
failure to do this may cause the power cord
coating to melt, resulting in a fire or electrical
shock.
Avoid the following situations:
If excessive stress is applied to the connection
part of the power cord, it may damage the
power cord or the wires inside the machine may
disconnect. This could result in a fire.
– Connecting and disconnecting the power cord
frequently.
– Tripping over the power cord.
– The power cord is bent near the connection
part, and continuous stress is being applied to
the power outlet or the connection part.
– Applying excessive force on the power plug.
CAUTION
Install this machine near the power outlet and
•
leave sufficient space around the power plug
so that it can be unplugged easily in an
emergency.