Numeric Buttons; Station Presets; Frequency Direct Button; Direct Access Tuning - Rotel RT-02 Manual De Instrucciones

RT-02 AM/FM Stereo Tuner

NUMERIC Buttons:

Station Presets

A
5
The RT-02 can store up to 30 station presets
for recall at any time using the NUMERIC
keypad. These station presets can be used
for any combination of AM stations and FM
stations.
The RT-02 is delivered from the factory with a set
of generic station presets that may or may not
match any available stations in your area.
To memorize a new station preset:
1. Tune to the desired station, AM or FM.
2. Press the MEMORY button on the front
panel. A MEMORY indicator will flash in
the front panel display.
3. While the MEMORY indicator is flashing,
press the number of the preset where you
wish to store the station frequency. For
example, to memorize the station as preset
3, press the 3 button. To memorize preset
15, press the 1 button followed by the 5
button.
4. A previously stored frequency is erased
from memory when a new frequency is
memorized for the same preset number.
To tune to a previously memorized
station preset, press the preset num-
ber using the NUMERIC buttons. For
example, to tune to preset 3, press the 3 button.
To tune to preset 30, press the 3 button and
then press the 0 button within 5 seconds.
NOTE: The NUMERIC buttons can also be
used for FREQUENCY DIRECT tuning.

FREQUENCY DIRECT Button:

Direct Access Tuning

Remote Only
If you know the exact frequency of the desired
station, you may tune it directly using the
FREQUENCY DIRECT button (remote only)
and the NUMERIC buttons.
1. Press the FREQUENCY DIRECT button to
change the NUMERIC buttons from station
preset to direct access mode. The station
frequency in the front panel display will
change to a series of bars, representing
the digits of a station frequency, with the
first bar blinking.
2. Enter the first digit of the station frequency
using the NUMERIC buttons. The digit will
appear in the frequency display and the next
bar will flash. Enter the remaining digits of
the frequency. When all of the digits have
been entered, the tuner will automatically
tune to the displayed station frequency.
NOTE: On the USA version only, pressing
1 in the FM mode will enter 10 as the digit
in the frequency display. On the European
version, it is necessary to press 1 and then
0 to enter 10. For US FM stations, press
only one digit following the decimal point
as shown in the first example following. For
European FM stations, press two digits after
the decimal point as shown in the second
example.
EXAMPLES:
(USA FM) 87.50MHz
(Europe FM) 87.50MHz
(USA AM) 1610kHz
(Europe AM) 1611kHz
If no frequency is entered within 5 seconds,
the tuner will cancel FREQUENCY DIRECT
tuning mode and revert to the last previously
tuned station.

Auto Tuning Button

The AUTO TUNING button toggles between
the frequency search tuning feature and
manual frequency tuning. When using the
TUNING controls on the front panel or remote
in AUTO TUNING mode, the tuner will begin
automatically scanning up or down through the
frequencies until the next receivable broadcast
signal is detected. If this is not the desired sta-
tion, use the TUNING controls again to find
the next station. Weak stations will be skipped
during auto tuning. If no receivable signal is
detected, the tuner will revert to the previously
C tuned station.
To toggle between FREQUENCY TUNING
mode and AUTO TUNING mode, press the
AUTO TUNING button. An AUTO indicator
will appear in the display.
NOTE: AUTO TUNING mode is disen-
gaged when the TUNE/PRESET button is set
to PRESET tuning mode. See the following
section.
8

TUNE/PRESET Button

The TUNE/PRESET button toggles between
FREQUENCY TUNING mode (the TUNING
controls advance to the next station frequency)
and PRESET TUNING mode (the TUNING
controls advance to the next memorized station
preset). To toggle between the two modes, press
the TUNE/PRESET button. A PRESET indicator
in the front panel DISPLAY will light when the
PRESET mode is active.
NOTE: AUTO TUNING mode is disen-
gaged when the TUNE/PRESET button is set
to PRESET tuning mode.

PRESET SCAN Button

This button activates a preset scanning feature.
When you press the button, the tuner will
automatically scan through all memorized
station presets, playing each for five seconds
before moving to the next. To stop the station
Press 8>7>5
scanning on the desired station preset, press
Press 8>7>5>0
the button again.
Press 1>6>1
Press 1>6>1>1 NOTE: If a PRESET station is currently tuned
when the PRESET SCAN button is pressed,
scanning will start with the next higher pre-
set number and continue through all preset
stations, stopping on the initial preset. If a
PRESET station is not currently tuned when
8 J the button is pressed, scanning will start
from PRESET 1 and continue to PRESET 30.

FM MONO Button

Remote Only
The FM MONO button changes the FM mode
from stereo reception to mono reception. In
stereo mode, a stereo signal will be heard if the
station is broadcasting a stereo signal and there
is sufficient signal strength. A stereo indicator
will light in the front panel display. In mono
mode, a mono signal will be heard even if the
station is broadcasting a stereo signal.
NOTE: Switching to mono mode can be a
useful way to improve the reception of weak
or distant FM signals. Less signal strength is
required for clean mono reception than for
stereo reception.
K
9
0 D
I