Tripp-Lite APS Serie El Manual Del Propietario página 7

Configuration
Select Battery Charger-Limiting
Points—OPTIONAL
(Not on 612, 750 or 1250 Models)
Most Limiting (#B1 & #B2 Up, factory set-
ting): Charger-limiting takes effect the
moment any 120V AC load is applied; charger output falls gradual-
ly from full output at no 120V load passing through to no output at
full load.
Less Limiting (#B1 Down & #B2 Up):
Charger-limiting begins
Inverter/Charger's load reaches 33% of the
Inverter/Charger's load rating. Charger
output falls gradually from full output at
33% of the Inverter/Charger's load rating to about 33% of full output
at full load.
Select Equalize Battery Charge—OPTIONAL
B3
(Not on 612, 750 or 1250 Models)
This DIP Switch is momentarily engaged
to begin the process of equalizing the
charge state of your battery's cells by time-
limited overcharge of all cells. This can
extend the useful life of certain types of batteries; consult with your
battery's manufacturer to determine if your batteries could benefit
from this process. The charge equalization process is automatic;
once started, it can only be stopped by removing the input power.
Set Battery Charging Amps—OPTIONAL
B4
(Not on 612, 750 or 1250 Models)
Check specifications for your unit's high-
and low-charging amp options. By setting
on high charging, your batteries will
charge at maximum speed. When setting
on low charging, you lengthen the life of
your batteries (especially smaller ones).
Set Battery Charge Conserver (Load Sense) Control—OPTIONAL (Not on 612, 750 or 1250 Models)
In order to save battery power, the unit's inverter automatically shuts off in the absence of any power demand from
connected equipment or appliances (the electrical load). When the Inverter/Charger detects a load, it automatical-
ly turns its inverter function on. Users may choose the minimum load the Inverter/Charger will detect by adjusting
the Battery Charge Conserver Control (see diagram). Using a small tool, turn the control clockwise to lower the
minimum load that will be detected, causing the inverter to turn on for smaller loads. When the control is turned
fully clockwise, the inverter will operate even when there is no load. Turn the control counterclockwise to increase the minimum load that
will be detected, causing the inverter to stay off until the new minimum load is reached.
NOTE: The factory setting for the control is fully clockwise. However, based on the threshold load to which you'd like the inverter to respond, you should adjust the control counterclockwise to reduce
its sensitivity until the inverter is active only when connected equipment or appliances are actually in use.
Connect Remote Control—Optional (All models)
All models feature an 8-conductor telephone style receptacle on the front panel for use with an optional remote control module (Tripp Lite
model APSRM4, sold separately or included with select models). The remote module allows the Inverter/Charger to be mounted in a compart-
ment or cabinet out of sight, while operated conveniently from a remote location. See instructions packed with the remote control module.
Connect Battery Temperature Sensing Cable—OPTIONAL (Select Models)
The battery temperature sensing function prolongs battery life by adjusting the charge float voltage level based on battery temperature. Connect
the sensor cable (the cable, included with select models, has an RJ style connector on one end and a black sensor on the other) to the RJ
style jack located on the side of the Inverter/Charger labeled "Remote Temp. Sense." Affix the sensor to the side of your battery below the
electrolyte level. To guard against false readings due to ambient temperature, place the sensor between batteries, if possible, or away from
sources of extreme heat or cold. If the sensor cable is not used, the Inverter/Charger will charge according to its default 25º C values.
(continued)
B4 B3 B2
B4 B3 B2
when the
B4 B3 B2 B1
B4 B3 B2 B1
Least Limiting (#B1 Up & #B2 Down):
B1
Charger-limiting begins at when the
Inverter/Charger's load reaches 66% of the
Inverter/Charger's load rating. Charger
output falls gradually from full output at
66% of the Inverter/Charger's load rating to about 66% of full output
at full load.
No Limiting (#B1 & #B2 Down): No
charger-limiting occurs at any load size.
B1
Setting Procedure
• Move to "Equalize" (DOWN) position for three seconds.
Reset
• Move to "Reset" (UP) position and leave it there. This is the
factory default setting.
Equalize
CAUTION: Do not leave DIP switch #3 in the down position after beginning process. Battery
charge equalization should only be performed in strict accordance with the battery manufacturer's
instructions and specifications.
Battery Charge
Reset
Equalize
Battery Charger
Low Charge Amps
High Charge Amps
CAUTION: When switching to the High Charge Amp setting, the user must ensure that the amp
hour capacity of their battery system exceeds the amperage of the High Charge Amp setting or
the batteries may be damaged or degraded.
7A
B4 B3 B2 B1
B4 B3 B2 B1
Switch Position
Up (factory setting)
Down—momentarily
Switch Position
Up (factory setting)
Down
OFF
MAX
(GREATER (LESSER
LOAD
LOAD
ON)
ON)