Kenwood KDC-X700 Manual De Instrucciones página 26

AUDIO SETTINGS
LOUDNESS LEVEL1/ LEVEL2: Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low
volume level. ; OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
FADER R15 to F15 (0): Adjusts the rear and front speaker output
balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output
balance.
VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source.
(Before adjustment, select the source you want to adjust.)
SOUND EFFECT
SOUND RECNSTR (Not applicable for TUNER source, AUX source and SIRIUS XM source.)
(Sound reconstruction) ON: Creates realistic sound by compensating the high-
frequency components and restoring the rise-time of
the waveform that are lost in audio data compression. ;
OFF: Cancels.
SPACE ENHANCE (Not applicable for TUNER source.)
SMALL/ MEDIUM/ LARGE: Virtually enhances the sound
space. ; OFF: Cancels.
SND REALIZER LEVEL1/ LEVEL2/ LEVEL3: Virtually makes the sound more
realistic. ; OFF: Cancels.
STAGE EQ LOW/ MIDDLE/ HIGH: Virtually adjust the sound position
heard from the speakers. ; OFF: Cancels.
DRIVE EQ ON: Boosts the frequency to reduce the noise heard from
outside the car or running noise of the tyres. ; OFF: Cancels.
22
SPEAKER SIZE
FRONT SIZE
TWEETER
REAR 3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8/ 6×9/ 7×10:
Selects according to the connected speaker size for optimum performance. ;
NONE: Not connected.
SUBWOOFER 6.5"/ 8"/ 10"/ 12"/ 15" OVER: Selects according to the connected speaker
size for optimum performance. ; NONE: Not connected.
X ' OVER
TWEETER FRQ
GAIN LEFT
GAIN RIGHT
FRONT HPF F - HPF FRQ
F - HPF SLOPE
F - HPF GAIN
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/
6×8/ 6×9/ 7×10: Selects according to the connected
speaker size for optimum performance.
SMALL/ MIDDLE/ LARGE: Selects according to the
size range of the connected tweeter for optimum
performance. ; NONE: Not connected.
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/
8KHZ/ 10KHZ/ 12.5KHZ: Adjusts the crossover
frequency for the tweeter speaker.
–8 to 0: Adjusts the output volume of the left tweeter.
–8 to 0: Adjusts the output volume of the right tweeter.
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ:
Adjusts the crossover frequency for the selected
speakers (high pass filter). ; THROUGH: All signals are
sent to the selected speakers.
–6DB/ –12DB/ –18DB/ –24DB: Adjusts the
crossover slope. (Selectable only if a setting other than
[THROUGH] is selected for [F - HPF FRQ].)
–8 to 0: Adjusts the output volume of the selected
speaker.