Parma 707 Instrucciones De Montaje página 9

ASSEMBLY AND USER INSTRUCTIONS
Whenever this product is used the following information must be
taken into consideration: the bike rack is a safe product if used
correctly, but if it is used incorrectly it can cause damages to you
and to anyone driving behind you.
1) Insert the plugs 1 in the square bearing tubes 2 (Fig. A).
2) Insert the plugs 3 in the tilt device tube 4 (Fig. A) and in the bike fixing
arch 5 (Fig. F2).
3) Attach the hook 6 to the tilt device 7 (Fig. A).
4) Mounting the aluminium tyre cradles 8: carry out the preliminary
operations as per the instructions B1-B2-B3 (Fig. B), attach the
cradles to the square bearing tubes 2 with interposed shims 9, then fix
them with the washers and nuts 10 (Fig. B).
5) Mount the rear lights 11 to the lighting board 12 and fix together with
the washers and nuts 13 (Fig. C); take care not to damage the wires and
not to over-tighten the nuts as this could damage the plastic parts.
Thread the 13 pin plug through the central hole of the lighting board 12.
6) Fix the number plate frame 14 to the light bar 12 with the screws 15 .
7) Fix the lighting board assembly 12 to the square tube 16 with the
screws 17, the nuts and the washers 18; make sure you thread the tilt
hook 6 into the slot provided (Fig. D).
8) Mounting the bike loader rail 19: carry out the preliminary operations as
per the instructions E1-E2 (Fig. E), then mount it on the lighting board
12 and fix with the knobs 20 (Fig. E).
9) Mounting the bike fixing arch 5:
- Undo and remove the knobs 21 and the washers 22 from both sides
(Fig. F1);
- Place the bike fixing arch 5 in the half pipe of the tilt adjustment
element 23, then fix it with the washers 22 and the knobs 21 (Fig. F2).
HOW TO INSTALL THE BIKE CARRIER ON
THE TOWBALL
For personal safety and to avoid damaging the vehicle we recommend 2
people mount the bike rack.
10) Push the lever 24 upwards, to disengage it turn the wrench 25 counter
clockwise (Fig. G1).
11) Place the fixing block 27 on the towball 26 (Fig. G2).
12) Close the clamping device by lowering the lever 24: at least 45 kg.
clamping force is required. (Fig. G2).
Adjustment of closing hand force
It is always necessary to make the first adjustment when the product is
purchased. Then, every time the product is used, the clamping force must
be checked and adjusted if necessary. In order to prevent accidents and
damage it is advisable to ask a second person to assist you in this
procedure as well. After disengaging and lifting the lever 24 the second
person must hold the cycle carrier in a horizontal position. The screw 28
must be adjusted with the wrench provided 29 so that the clamping
force on the lever is increased to a minimum of 45 Kg. (Fig. G2). Make
sure that the bike rack does not rotate when the clamping device has
been locked.
POSITIONING AND FIXING THE BIKES ON
THE BIKE RACK
13) Use the rail 19 to facilitate loading the bike: to attach it to the aluminium
tyre cradle 8 follow instructions H1-H2 (Fig. H).
707_PARMA E-BIKE_18/09/18
707_PARMA E-BIKE_05/06/2020
EN
14) Position the biggest, heaviest bike near the car, place the wheels on
the aluminium cradle 8 and lean it against the fixing arch 5. Fasten
the bike to the fixing arch 5 with the arm 30 (Fig. I2). Fasten the
wheels with the fixing straps 31 (Fig. I1).
15) Repeat operations 14) for the second bike.
: For safe transportation of the load the bike carrier is
IMPORTANT
supplied with a strap 32 for tying all the bikes to the fixing arch 5.
Check that the belt is mounted correctly by pulling on it.
BIKE RACK INCLINATION
To tilt the bike rack hold it up with one hand while you pull the hook 6
with the other (Fig. L). To avoid injury or damage, this operation of
tilting the bike rack should be carried out with the help of a third person.
To close the bike rack, lift it until the tilt mechanism 7 engages
completely by passing from the tilt position (Fig. M) to the closed
position (Fig. N).
ATTENTION – SAFETY REQUIREMENTS
As well as the information described below please observe the
"
Conditions, suggestions and limits for use
type test certificate.
- Weight and maximum capacity of "PARMA E-BIKE" bike racks:
* Model 707 (17,00 kg.) ---> 2 bikes, max. capacity 60 kg.
- Never exceed the permitted capacity of the towing hook installed. The
combined weight of the bike rack and the load must never exceed the
permitted capacity. Keep the towing hook ball surface clean from dirt
and oil.
- The driver is always responsible for the load he is transporting and
consequently he is also responsible for checking the fastenings both
before starting the trip and at regular intervals during the trip.
- Check the car manual for the specifications concerning the maximum
permissible rear axle weight.
- Verify compliance with the value D (maximum load bearing capacity)
of the towball specified by the car or towball manufacturer; the value
D for the towball must be at least (760 Kg) 7.6kN; older towballs
often only specify the permissible load on the towball G
total permissible load of the towing vehicle G
this case the value D can be calculated using the values specified in
the vehicle maintenance or registration booklet:
9,81 (G G )
x
A K
x
D =
1000 (G G )
A + K
(D in [kN] / G in [kg] / G
A
- Remove from the transported bikes children's seats, transport
baskets, rain covers or other elements that could get lost or increase
the air resistance.
- Do not carry more bikes than the number indicated for a specific
model.
- Bike parts, such as for example the handlebars or pedals, must not be
left in the normal position of use; they must be folded to avoid
dangerous projections.
- Ensure that the bike rack is fitted correctly on the towing hook and
that the bikes are secured as instructed.
- The bike rack is only suitable for transporting bicycles.
9/32
9/32
(Fig. L/M/N)
" specified in the EC
rather than value D; in
K
in [kg])
K
Copyright © 2012 Peruzzo Italy - MADE IN ITALY
Copyright © 2020 Peruzzo Italy - MADE IN ITALY
and the
A