Factory Setting (Reset); Calling Up The Event Log; Showing System Information Changing Device Ids And Device Names - Monacor IOR-204 Manual De Instrucciones

8.10 Factory setting (reset)

To reset the recorder to its factory settings:
1) Call up the main menu: Either press the button MENU
on the remote control or press the right mouse button to
show the toolbar and then click the icon
2) In the bar located at the top of the menu, click "Advanced".
Parameter Record Search Device
Maintain
Default User admin
Events
Auto Reboot Enable
Intelligent
Reboot Every Week
Update
Load Settings
IPC Load Default
Fig. 8-26 Menu "Advanced"
3) Click the field "Load Default".
Load Default
Display Device
Record System
Network Advanced
Alarm
All Clear Save
Fig. 8-27 Window "Load Default"
4) A reset to the factory settings can be performed for all or
specific setting types. The setting types listed correspond
to the menus or submenus of the same name. To select
setting types, click the respective fields with the mouse.
Menu item Function
(Display etc.) To select a specific setting type
All To select all setting types
Clear To deselect the setting types selected
To reset the selected setting types to their
Save
factory settings
Cancel To close the window

8.11 Calling up the event log

The recorder saves all events such as loss of camera signal,
switch-on and switch-off of the recorder, manual recording,
replay of a recording, changes to the menu settings etc.
Call up the menu "System" and then click the submenu "Log".
Parameter Record Search Device
General
Start Date 03/25/2018
3 0
Users
End Date 03/25/2018
3 0
Log Type All
Info
Channel Type
Log
System 03/25/2018 10:23:45
Intellient Ana
Comfig 03/25/2018 11:02:33
Comfig 03/25/2018 11:13:27
Comfig 03/25/2018 11:17:55
System
03/25/2018 11:20:04
System
03/25/2018 12:23:17
CH2 Alarm 03/25/2018 13:15:41
CH2 Alarm 03/25/2018 13:16:36
Abb. 8-28 Event list after a search query
"Main Menu".
i
System Advanced
Sun. 00:00
Load Default IPC Upgrade
Save Settings
Reboot IPC
Default Save
Cancel
i
System Advanced Shutdown
Start Time 00:00:00
End Time 23:59:59
Search
Time Operatopm Record Playback
System Startup
General Settings
Channel Add
Channel Add
Shutdown
System Startup
Motion Start Yes
Motion End Yes
<< 1/4 1 >>
Backup Cancel
Menu item
Start Date
End Date
Start Time
End Time
Log Type
Shutdown
Search
Backup
Cancel
To make sure that any tampering with the recorder is shown in
the log, the log entries will not be deleted when the hard disk
is formatted or when the recorder is reset to its factory settings.
Cancel
8.12 Showing system information
Changing device IDs and device names
1) Show the toolbar: Press the right mouse button or move
the mouse pointer to the centre of the lower edge of the
screen.
Fig. 8-29 Toolbar
2) Either press the icon
is immediately shown) or click the icon
and then, in the main menu, select the menu "System"
and then click the submenu "Info". The section "Info"
will be selected:
Parameter Record Search
General
Device ID
Users
Device Name
Device Type
Info
Hardware Version
Info
Software Version
Channel Info
IE Client Version
Record Info
IP Address
Log
MAC Address
Intelligent Ana HDD Volume
Video Format
P2P ID
Fig. 8-30 System information
when the system information is shown by means of the icon
the menu bar at the top of the screen and the submenus to
the left will not appear
In the line "Device ID", a user-defined identification number
can be entered, e.g. when multiple recorders are to be accessed
via a network. The recorders can only be addressed separately
when they have different ID numbers.
In the line "Device Name", a different name can be entered
so that it will be easier to distinguish multiple recorders from
each other by their name.
Two additional sections provide further information (unless the
i
icon has been used to show the information):
"Channel Info": Information with regard to the camera channels
"Record Info": Information with regard to the recording settings
If required, refer to the menu overview in chapter 7.6.
Function
First day
Last day
of the search query
Beginning
i
End
To select the event type:
All, System, Config, Alarm, Account,
Record, Storage
The event types are shown in the list column "Type".
To start a search query
To save the event list to a USB flash drive,
for example
To close the window
i
(Info) on the far right (the information
i
Device System Advanced
000000
1080P-HY04N
HY-DVR
DM-284
V7.1.0-20160719
V2.0.0.867
192.168.1.159
00-23-63-63-FR-A7
931G
PAL
RSV160700970782
i
on the far left
Shutdown
QR code
P2P ID
Save Cancel
i
,
55