Char-Broil Gourmet T-36D Guía Del Producto página 5

Sideburner Ignitor Lighting
• Do not lean over grill while lighting.
1. Turn OFF all gas burner control valves.
2. Turn ON gas at LP cylinder.
3. To ignite SIDEBURNER, open sideburner cover.
4. Turn sideburner knob to the position.
5. Push and hold ELECTRONIC IGNITOR button until
the burner lights.
6. Once burner has ignited, turn knob to desired
setting.
7. If sideburner does not light, turn knob to
wait 5 minutes, then repeat lighting procedure.
Sideburner Match Lighting
• Do not lean over grill while lighting.
1. Open lid during lighting. Turn ON gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to the position. Be sure
burner lights and stays lit.
Burner Flame Check
• Remove cooking grates and troughs. Light burners,
rotate knobs from to . You should see a
smaller flame in position than seen on
Perform burner flame check on side burner, also. Always
check flame prior to each use. If only low flame is seen
refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Turning Grill Off
• Turn all knobs to the OFF position. Turn LP cylinder
OFF by turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic
ignitor button. "Click" should be heard and spark seen
each time in each collector box or between burner and
electrode. See "Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in OFF position. To check
valves, first push in knobs and release, knobs should
spring back. If knobs do not spring back, replace valve
assembly before using grill. Turn knobs to LOW position
then turn back to OFF position. Valves should turn
smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn or
kinked. Replace damaged hoses before using grill. Use
only valve/hose/regulator specified by manufacturer.
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
OFF,
If your grill is getting hard to light or the flame is weak,
check and clean the venturis and burners.
Spiders or small insects are known to create
"flashback" problems by building nests and laying
eggs in the barbeque's venturi or burner, obstructing
the flow of gas. The back-up gas can ignite behind
the control panel. This flashback can damage your
barbeque and cause injury. To prevent flashbacks
and ensure good performance the burner and venturi
tube assembly should be removed and cleaned when
ever the barbeque has been idle for an extended
period of time.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease
and smoke for paint. Interiors of gas grills are not
painted at the factory (and should never be painted).
Apply a strong solution of detergent and water or use a
grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry. Do not
apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
• Do not use citrisol, abrasive cleaners, degreasers or a
.
concentrated grill cleaner on plastic parts. Damage to
and failure of parts can result.
• Porcelain surfaces: Because of glass-like composition,
most residue can be wiped away with baking
soda/water solution or specially formulated cleaner. Use
nonabrasive scouring powder for stubborn stains.
• Painted surfaces: Wash with mild detergent or
nonabrasive cleaner and warm soapy water. Wipe dry
with a soft nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill's high
quality appearance, wash with mild detergent and
warm soapy water and wipe dry with a soft cloth after
each use. Baked-on grease deposits may require the
use of an abrasive plastic cleaning pad. Use only in
direction of brushed finish to avoid damage. Do not
use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean
any of the grill cooking surfaces, ensure no loose
bristles remain on cooking surfaces prior to grilling. It is
NOT recommended to clean cooking surfaces while
grill is hot.
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP cylinder is connected to grill, store outdoors
in a well-ventilated space and out of reach of
children.
• Cover grill if stored outdoors. Choose from a variety of
grill covers offered by manufacturers.
• Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
• When removing grill from storage, follow "Cleaning the
Burner Assembly" instructions before starting grill.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of
burner assembly or if you have trouble igniting grill.
1. Turn gas OFF at control knobs and LP cylinder.
2. Remove cooking grates and troughs.
3. Remove cotter pins and carryover tubes from front of
burners.
4. Remove cotter pin and lift burner to disengage from
5. Use flat blade screwdriver to pry off electrode from
6. Carefully lift each burner up and away from valve
We suggest three ways to clean the burner tubes. Use
the one easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works
(B) Use a narrow bottle brush with a flexible handle (do
(C) Wear eye protection: Use an air hose to force air
7. Wire brush entire outer surface of burner to remove
8. Clean any blocked ports with a stiff wire such as an
9. Check burner for damage, due to normal wear and
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustrations at right.
10. Attach electrode to burner.
11. Carefully replace burners.
12. Attach burners to brackets on firebox.
13. Reposition carryover tubes and attach to burners.
Replace troughs and cooking grates.
5
bracket on firebox.
burner. Electrode should remain in firebox.
openings.
well) into a small hook. Run the hook through each
burner tube several times.
not use a brass wire brush), run the brush through
each burner tube several times.
into the burner tube and out the burner ports. Check
each port to make sure air comes out each hole.
food residue and dirt.
open paper clip.
corrosion some holes may become enlarged. If any
large cracks or holes are found replace burner.
Correct burner-to-valve
engagement
Firebox
Firebox Burner
Support
Electrode
Firebox
Electrode
Pry off electrode
Firebox Burner
with a flate blade
Support
screwdriver
Remove
screws