Makita GA4040C Manual De Instrucciones página 5

ENGLISH
(Original instructions)
1 Shaft lock
2 Slide switch
3 Indication lamp (speed adjust-
ing dial)
4 Speed adjusting dial
5 Wheel guard
6 Bearing box
7 Screw
8 Lever
9 Lock nut
10 Depressed center wheel
11 Inner flange
SPECIFICATIONS
Model
Wheel diameter
Max. wheel thickness
Spindle thread
Rated speed (n) /
No load speed (n )
0
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
Explanation of general view
12 Lock nut wrench
13 Ezynut
14 Abrasive wheel
15 Spindle
16 Arrow
17 Notch
18 Flex wheel
19 Plastic pad
20 Sanding lock nut
21 Abrasive disc
22 Rubber pad
23 Marking A
GA4040C GA4041C
100 mm (4")
6.4 mm
M10
–1
11,000 min
303 mm 325 mm
2.3 kg 2.6 kg
GA4540C GA4541C
115 mm (4-1/2")
M14 or 5/8" (country specific)
–1
11,000 min
303 mm 325 mm
2.5 kg 2.7 kg
/II
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
ENE048-1
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
ENF002-2
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
GEA010-1
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
24 Marking B
25 Marking C
26 Marking D
27 Abrasive cut-off wheel/diamond
wheel
28 Wheel guard for abrasive cut-off
wheel/diamond wheel
29 Wire cup brush
30 Wire wheel brush
31 Exhaust vent
32 Inhalation vent
GA5040C/
GA5041C
GA5040CN
125 mm (5")
7.2 mm
–1
11,000 min
303 mm 325 mm
2.5 kg 2.7 kg
GA6040C
150 mm (6")
6.4 mm
–1
9,000 min
303 mm
2.6 kg
GEB033-9
5