Bosch GSA 36 V-LI Professional Manual Original página 15

OBJ_BUCH-303-007.book Page 15 Wednesday, September 21, 2016 10:32 AM
Sabre saw
Weight according to EPTA-
Procedure 01:2014
Permitted ambient temperature
– during charging
– during operation* and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =1.5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =23.0 m/s , K=1.5 m/s
h
2
Cutting wooden beam: a =24.0 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different ap-
plications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-11,
EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Bosch Power Tools
Henk Becker
GSA 36 V-LI
Executive Vice President
Engineering
kg 3.8 – 4.4
°C 0...+45
Robert Bosch Power Tools GmbH
°C –20...+50
70538 Stuttgart, GERMANY
GBA 36V ...
Stuttgart, 01.01.2017
AL 36..
Assembly
GAL 36..
Battery Charging
 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
 Do not continue to press the On/Off switch after the
2
,
machine has been automatically switched off. The bat-
2
.
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 10 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 9 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 10:
– Push the battery against the base of the power tool (1.) and
at the same time press the battery unlocking button 9 (2.).
– Pull the battery out of the power tool until a red stripe be-
comes visible (3.).
– Press the battery unlocking button 9 again and pull out the
battery completely.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
12 indicate the charge condition of the battery 10. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Push button 13 to indicate the charge condition (also possi-
ble when the battery is removed). The battery charge-control
indicator automatically goes out after approx. 5 seconds.
English | 15
Helmut Heinzelmann
Head of Product Certification
PT/ECS
1 609 92A 2MY | (21.9.16)