Change Parameters - Parker Hyperchill-Plus Manual De Uso

PARAMETER CODE
Temperature control diff erential
(NOT visible with code " CPt= dIFI
On")
4.4.3 Energy saving temperature control
PARAMETER CODE
ESE
energy saving enable
Set energy saving
SEt_ES
4.4.4 Compressor parameters
PARAMETER CODE
dAS
Minimum `On' time.
Minimum time between two
dES
compressor switch-ons.
AbCI
Compressor hour counter 1
4.4.5 General parameters
PARAMETER CODE
CPt
precision control enable
4.4.6 B1, B2 sensor parameters
PARAMETER CODE
High temperature alarm
HA1
(water)
Low temperature alarm (water)
LA1
High temperature alarm
HA2
(evaporator)
Low temperature alarm
LA2
(evaporator)
English

4.5 Change parameters

TYPE DEFAULT
Parameter (SEt / dIFI/ dEF )
4.5.1
3
C°
Fig.2
D
5.4
F°
esc
set
TYPE DEFAULT
PAr
OFF
D
20.0
C°
set
D
68.0
F°
TYPE DEFAULT P_nA
2
F
F
5
0
D
set
TYPE DEFAULT
OFF
U
TYPE DEFAULT
60
C°
D
140
F°
CF30
-20
C°
U
-4
F°
60
C°
4.5.2 Water temperature setting (see fi g.1/2)
U
140
F° 1. Turn the main swicth (QS) to "ON" and wait for the "OFF" visu-
alization.
3
C°
U
37.4 2. Press the buttons "
F°
type "D" .
3. Select the parameter "PAr"using "
press the button "
4. Select the parameter "tEr"using "
press the button "
5. Select the parameter "SEt"using "
press the button "
6. Change the value using "
tEr CnP PbI
r9E
set
set
set
HA1
Ar9
set
C1H2
C1H
SEt diFI
CF31 CF32
dEF
esc
set
" " " together to enter on the parameter
"and " " buttons and
set
" to enter.
"and " " buttons and
set
" to enter.
"and " " buttons and
set
" to enter.
"and " " buttons and press the but-
ICEP002 (60Hz)
set
ton " " to confi rm and exit.
esc
7. Press the button " " three times to exit.
4.5.3 Diff erential setting (see fi g.1/2)
1.Turn the main swicth (QS) to "ON" and wait for the "OFF" visuali-
zation.
esc
set
2.Press the buttons " " " " together to enter on the parameter
type "D"
3.Select the parameter "PAr"using " "and "
set
press the button " " to enter.
4. Select the parameter "tEr"using " "and "
set
press the button " " to enter.
5. Select the parameter "dIFI"using "
set
press the button " " to enter.
6. Change the value using " "and " " buttons and press the but-
set
ton " " to confi rm and exit.
esc
7. Press the button " " three times to exit.
4.5.4 Restore default parameters (see fi g.1/2)
1.Turn the main swicth (QS) to "ON" and wait for the "OFF" visuali-
zation.
esc
set
2.Press the buttons " " " " together to enter on the parameter
type "D"
3.Select the parameter "PAr"using " "and "
set
press the button " " to enter.
4. Select the parameter "P_nA"using "
set
press the button " " to enter.
5. Select the parameter "dEF"using "
set
press the button " " to enter.
6. Change the value "OFF" to "On" using "
set
and press the button " " to confi rm and exit.
esc
7. Press the button " " three times to exit.
" buttons and
" buttons and
"and " " buttons and
" buttons and
"and " " buttons and
"and " " buttons and
"and " " buttons
5 / 8