Campbell Hausfeld AL2150 Manual Del Usuario página 4

Operating Instructions and Replacement Parts List
SOLVENT
Figure 4 - Prevent Clogged Tip
Spraying Instructions (Cont.)
2. Point gun in a safe direction and spray.
This should clear tip of any blockage.
3. Rotate the tip back to the spray posi-
tion and continue spraying (See Fig. 5).
4. If clogging continues, replace gun filter
and consider straining the paint prior
to use.
CLEAN
Figure 5 - Clean and Spray Position
can occur if a needle or sharp object is
used to clean the tip. Tungsten carbide
is brittle and can be chipped.
FIXED TIP:
1. Depressurize and turn off the unit
per manufacturer's instructions.
2. Lock gun trigger.
3. Remove tip and tip guard from the gun.
4. Soak tip in water or appropriate sol-
vent and brush away old paint or
impurities with a toothbrush until
the tip orifice has been cleared.
ADJUSTABLE TIP:
1. Turn adjustment knob fully counter-
clockwise to open tip to largest spray
pattern.
2. Pull trigger and spray into a bucket
or container. This should clear the tip
of any blockage.
3. If clogging continues, replace gun fil-
ter and consider straining the paint
prior to use.
CLEANING YOUR GUN: Follow clean-
ing, use and maintenance instructions
included with your paint sprayer. After
flushing the pump and when finishing:
1. Rotate Spray Tip to the cleaning
position.
www.chpower.com
2. Release Trigger Lock.
3. Point Spray Gun into an empty waste
bucket and pull the Trigger. Spray at
least 1 gallon of fluid into waste
bucket. To reduce splashing, direct
the fluid stream along the inside of
the bucket and well above the fluid
level.
REFER TO PAINT SPRAYER SHUT-
DOWN PROCEDURES.
4. Depressurize and turn off sprayer per
manufacturer's instructions.
5. With the gun pointed in a safe direc-
tion, pull the gun trigger with the
trigger lock disengaged to ensure
system is depressurized.
6. Engage Trigger Lock.
7. At this point the pump and spray
gun are clean, but still require prepa-
ration for storage. Spray Tip Guard
or any accessory being used still
require cleaning.
CLEANING SPRAY TIP GUARD:
1. Remove Spray Tip with 1" or
adjustable wrench.
2. Clean Tip Guard with a cleaning
SPRAY
brush.
Maintenance
Equipment
damage
may occur if these instructions are not
followed.
ing any maintenance, make sure to
relieve pressure from system and dis-
connect power from sprayer.
•
Do not use oil based solvents to
clean equipment after using latex
based coatings. Use only warm
soapy water.
•
Always replace clogged gun filters,
do not attempt to clean them.
•
Carefully follow cleaning and stor-
age instructions for your sprayer.
•
Do not use metal or other hard
objects to pick dried paint material
from Spray Tip Orifice.
TRIGGER LOCK
Pulling the trigger
must not open the gun
valve when trigger
lock is activated.
You should be able to
get the actuator to wiggle slightly with
your finger while holding the trigger
against the trigger lock when it is in
the locked position. If you cannot,
adjust the trigger position by following
these instructions:
1. Place trigger in locked orientation
2. With one hand holding trigger
3. Reverse the nut (counterclockwise)
TIP SEAL AND WASHER
Occasionally, you will need to replace
the silver seal and black washer located
inside the tip base.
1. To replace seal and washer, first
2. Remove spray tip.
3. With Phillips screwdriver, push seal
4. With flat side of seal facing up,
5. Place washer in base. Make sure it
Pump
damage
6. Put spray tip back in tip base.
7. Reattach tip base to gun valve.
Before
perform-
Make sure spray tip and
tip base fit snugly in
place. A loose fit can
lead to misdirected
spray discharge and a
skin injection hazard.
4
(tabs horizontal).
lightly against lock, use a 1/4" nut
driver to turn nut in until trigger
starts to come off the lock.
1/2 turn.
loosen tip base with adjustable
wrench, and then remove by hand.
and washer out from front of tip
base.
place seal in base. Make sure it lines
up properly with base.
lines up properly with base.