Victron energy MultiGrid 12/3000/120 - 50/230/240V Manual Del Usuario página 19

5.5.2 Step 2: Other settings
The remaining settings are not relevant for slaves.
Some of the remaining settings are not relevant for followers (L2, L3). These settings are imposed on the whole system by the leader
L1. If a setting is irrelevant for L2, L3 devices, this is mentioned explicitly.
ds8-ds7: Setting charging voltages (not relevant for L2, L3)
Absorption Float
ds8-ds7
voltage voltage
14.1 13.8
off off 28.2 27.6
56.4 55.2
14.4 13.8
off on 28.8 27.6
57.6 55.2
14.7 13.8
on off 29.4 27.6
58.8 55.2
15.0 13.8
on on 30.0 27.6
60.0 55.2
ds6: absorption time 8 or 4 hours (na for L2, L3)
ds5: adaptive charging algorithm (na for L2, L3)
ds4: dynamic current limiter
ds3: UPS function
ds2: converter voltage
ds1: converter frequency (na for L2, L3)
(the wide input frequency range (45-55 Hz) is 'on' by default)
Note:
- If "adaptive charging algorithm" is on, ds6 sets the maximum absorption time to 8 hours or 4 hours.
- If "adaptive charging algorithm" is off, the absorption time is set to 8 hours or 4 hours (fixed) by ds6.
Step 2: Exemplary settings
Example 1 is the factory setting (since factory settings are entered by computer, all DIP switches of a new product are set to 'off' and do
not reflect the actual settings in the microprocessor).
DS-8 Ch. voltage off
DS-7 Ch. voltage on
DS-6 Absorpt. time on
DS-5 Adaptive ch. on
DS-4 Dyn. Curr. limit off
DS-3 UPS function: on
DS-2 Voltage on
DS-1 Frequency on
Step 2 Step 2
Example 1 (factory setting): Example 2:
8, 7 GEL 14,4 V 8, 7 OPzV 14,1 V
6 Absorption time: 8 hours 6 Abs. time: 8 h
5 Adaptive charging: on 5 Adaptive ch.: on
4 Dynamic current limit: off 4 Dyn. Curr. limit: off
3 UPS function: on 3 UPS function: off
2 Voltage: 230 V 2 Voltage: 230 V
1 Frequency: 50 Hz 1 Frequency: 50 Hz
To store the settings after the DIP switches are set according to the required values: press the 'Down' button for 2 seconds (lower
button to the right of the DIP switches). The temperature and low-battery LEDs will flash to indicate acceptance of the settings.
The DIP switches can be left in the selected positions, so that the 'other settings' can always be recovered.
Storage
voltage
13.2 Gel Victron Long Life (OPzV)
26.4 Gel Exide A600 (OPzV)
52.8 Gel MK battery
Gel Victron Deep Discharge
13.2
Gel Exide A200
26.4
AGM Victron Deep Discharge
52.8
Stationary tubular plate (OPzS)
AGM Victron Deep Discharge
13.2
Tubular plate traction batteries in
26.4
semi-float mode
52.8
AGM spiral cell
13.2
Tubular plate traction batteries or
26.4
OPzS batteries in cyclic mode
52.8
DS-8 off DS-8 on
DS-7 off DS-7
DS-6 on DS-6 on
DS-5 on DS-5 on
DS-4 off DS-4 on
DS-3 off DS-3
DS-2 on DS-2
DS-1 on DS-1 on
Step 2
Example 3:
8, 7 AGM 14,7 V
6 Abs. time: 8 h
5 Adaptive ch: on
4 Dyn. Curr. limit: on
3 UPS function: off
2 Voltage: 240 V
1 Frequency: 50 Hz
Suitable for
on = 8 hours off = 4 hours
on = active off = inactive
(inactive = fixed absorption time)
on = active off = inactive
on = active off = inactive
on = 230 V off = 240 V
on = 50 Hz off = 60 Hz
DS-8 on
off DS-7 on
DS-6 off
DS-5 off
DS-4 off
off DS-3 on
off DS-2 off
DS-1 off
Step 2
Example 4:
8, 7 Tub.-plate 15 V
6 Abs. time: 4 h
5 Fixed abs. time
4 Dyn. Curr. limit: off
3 UPS function: on
2 Voltage: 240 V
1 Frequency: 60 Hz
17