Publicidad
Idiomas disponibles
Idiomas disponibles
English
introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
The Super Lift & Cut system ensures a close and easy
shave every day. For the best result, move the shaving
heads over your skin in both straight and circular
movements.
Replace the shaving heads every two years for optimal
shaving results.
general description (Fig. 1)
A Protection cap
B
Shaving unit
C Shaver on/off slide
D Mains plug
E
Appliance plug
F
Cleaning brush
g Trimmer slide (HQ6940 only)
h Trimmer (HQ6940 only)
important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
-
Keep the shaver and the mains cord dry (Fig. 2).
Warning
-
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
-
Children should be supervised to ensure that they
do not play with the appliance.
-
Do not use the shaver or the mains cord if it is
damaged.
-
If the mains cord is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
Caution
-
Always put the protection cap on the shaver
to protect the shaving heads when you are
travelling (Fig. 3).
-
Only use the mains cord supplied.
-
Store the appliance at a temperature between 5°C
and 35°C.
-
This appliance is not washable. Never immerse the
appliance in water, nor rinse it under the tap.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientific
evidence available today.
general
The appliance is equipped with an automatic voltage
selector and is suitable for mains voltages from 100 to
240 volts.
Using the appliance
shaving
1
Put the appliance plug in the shaver (Fig. 4).
2
Put the mains plug in the wall socket.
3
Push the on/off slide upwards to switch on the
shaver.
4
Move the shaving heads over your skin. Make both
straight and circular movements (Fig. 5).
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get accustomed to
the Philips shaving system.
5
Push the on/off slide downwards to switch off the
shaver.
6
Put the protection cap on the shaver every time
you have used it, to prevent damage (Fig. 3).
Trimming (hQ6940 only)
You can use the trimmer to trim your sideburns and
moustache.
1
Push the slide upwards to open the trimmer (Fig. 6).
The trimmer can be activated while the motor is running.
Cleaning and maintenance
Regular cleaning guarantees better shaving performance.
This appliance is not washable. Never immerse the
appliance in water, nor rinse it under the tap.
Never use scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the
appliance.
-
For easy and optimal cleaning, Philips Shaving Head
Cleaning Spray (type no. HQ110) is available. Ask
your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray may not be
available in all countries. Contact the Customer Care Centre
in your country about the availability of this accessory.
You can also clean the shaver in the following way:
Every week: shaving unit and hair chamber
1
Switch off the shaver. Remove the mains plug from
the wall socket and pull the appliance plug out of
the shaver.
2
Clean the top of the appliance first. Use the
cleaning brush supplied (Fig. 7).
3
Press the release button (1) and remove the
shaving unit (2) (Fig. 8).
4
Clean the inside of the shaving unit and the hair
chamber with the cleaning brush (Fig. 9).
5
Put the shaving unit back onto the shaver (Fig. 10).
Every two months: shaving heads
1
Switch off the shaver. Remove the mains plug from
the wall socket and pull the appliance plug out of
the shaver.
2
Press the release button (1) and remove the
shaving unit (2) (Fig. 8).
3
Turn the wheel anticlockwise (1) and remove the
retaining frame (2) (Fig. 11).
4
Remove the cutters and guards and clean them
with the cleaning brush supplied (Fig. 12).
Note: Do not clean more than one cutter and guard at a
time, since they are all matching sets. If you accidentally mix
up the cutters and guards, it may take several weeks before
optimal shaving performance is restored.
5
Clean the cutter with the short-bristled side of the
cleaning brush (Fig. 13).
Brush carefully in the direction of the arrow.
6
Brush the guard (Fig. 14).
7
Put the shaving heads back into the shaving unit.
Put the retaining frame back into the shaving unit,
push it down (1) and turn the wheel clockwise
(2) (Fig. 15).
8
Put the shaving unit back onto the shaver.
Extra thorough cleaning
For extra thorough cleaning, put the shaving heads in
a degreasing liquid (e.g. alcohol) every six months. To
remove the shaving heads, follow steps 1 to 4 described
above. After cleaning, lubricate the central point on the
inside of the guards with a drop of sewing machine oil to
prevent wear of the shaving heads.
Trimmer (hQ6940 only)
Clean the trimmer every time you have used it.
1
Switch off the shaver. Remove the mains plug from
the wall socket and pull the appliance plug out of
the shaver.
2
Clean the trimmer with the cleaning brush
supplied (Fig. 16).
Tip: Lubricate the trimmer teeth with a drop of sewing
machine oil every six months (Fig. 17).
storage
1
Put the protection cap on the shaver to prevent
damage (Fig. 3).
Replacement
Replace the shaving heads every two years for optimal
shaving results.
Replace damaged or worn shaving heads with HQ55
Philips Shaving Heads only.
1
Switch off the shaver. Remove the mains plug from
the wall socket and pull the appliance plug out of
the shaver.
2
Press the release button (1) and remove the
shaving unit (2) (Fig. 18).
3
Turn the wheel anticlockwise (1) and remove the
retaining frame (2) (Fig. 11).
4
Remove the shaving heads and place new ones in
the shaving unit (Fig. 12).
5
Put the retaining frame back into the shaving unit,
push it down (1) and turn the wheel clockwise
(2) (Fig. 15).
6
Put the shaving unit back onto the shaver.
Accessories
The following accessories are available:
-
HQ55 Philips Shaving Heads.
-
HQ110 Philips Shaving Head Cleaning Spray (not
available in China).
Environment
-
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment (Fig. 19).
guarantee & service
If you need service or information or if you
have a problem, please visit the Philips website at
www.philips.com or contact the Philips Consumer Care
Centre in your country (you find its phone number in
the worldwide guarantee leaflet). If there is no Consumer
Care Centre in your country, go to your local Philips
dealer.
guarantee restrictions
The shaving heads (cutters and guards) are not covered
by the terms of the international guarantee because they
are subject to wear.
Troubleshooting
This chapter summarises the most common problems
you could encounter with the appliance. If you are unable
to solve the problem with the information below, contact
the Consumer Care Centre in your country.
Problem
Cause
Reduced shaving
The shaving
performance.
heads are
dirty. You
have not
cleaned the
shaver well
enough or
you have
not cleaned
it for a long
time.
Long hairs
obstruct
the shaving
heads.
The shaving
heads are
damaged or
worn.
Solution
Clean the shaver
thoroughly before
you continue
shaving. See chapter
'Cleaning and
maintenance'.
Clean the cutters
and guards with
the cleaning brush
supplied. See chapter
'Cleaning and
maintenance', section
'Every two months:
shaving heads'.
Replace the shaving
heads every 2 years
for optimal shaving
results. See chapter
'Replacement'.
Publicidad
