Tabla de contenido
Publicidad
OUTDOOR USE
•
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
•
Before using the tool for the first time, it is recommended
to receive practical information
•
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
•
Always mount auxiliary handle E 6 and protective guard
F 6 ; never use the tool without them
•
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
•
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Dust from material such as paint containing lead, some
•
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
Be careful when cutting grooves, especially in supporting
•
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
•
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
•
Do not clamp the tool in a vice
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
Never use the tool when the cord is damaged; it must be
•
replaced by a specially prepared cord available through
an after-sales service centre for SKIL power tools and
carried out by a qualified person
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
•
In case of current interruption or when the plug
is accidentally pulled out, the tool will not restart
on its own; for restarting the tool unlock the on/off
switch 9 c and switch on tool again
AFTER USE
•
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
EXPLANATION OF SYMBOLS ON TOOL
2 Read the instruction manual before use
3 Wear protective glasses and hearing protection
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
•
If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
•
Mounting of accessories 6
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while pushing
spindle-lock button D
! push spindle-lock button D only when spindle A is
at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it (if provided)
•
Mounting of auxiliary handle E 7
! disconnect the plug
- screw auxiliary handle E on the right, the top, or the left
of the tool (depending on the work to be carried out)
Removing/mounting/adjusting of protective guard F 8
•
! disconnect the plug
- open protective guard F by loosening screw G (do not
remove it)
- place protective guard F on the spindle collar of the tool
head and turn it to the required position (depending on
the work to be carried out)
! ensure that the closed side of the protective guard
always points to the operator
- fasten protective guard F by tightening screw G
! firmly tighten screw G (min. torque 5 Nm)
•
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
•
On/off locking switch K 9
- switch on tool 9 a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 9 b
- unlock switch/switch off tool 9 c
! before switching off the tool, you should lift it from
the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
•
Grinding q
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting w
•
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on tool
head, in order to prevent the tool from being pushed out
of the cut in an uncontrolled manner
11
Publicidad
Tabla de contenido
