Optional Accessory - DeWalt DCF880 Manual De Instrucciones

There are three worklights 7
collar 3 . The worklights are activated when the trigger
switch is depressed. When the trigger is released, the
worklight will stay illuminated for up to 20 seconds. If
the trigger switch remains depressed, the worklights will
remain on.
nOTE: The worklights are for lighting the immediate work
surface and are not intended to be used as a flashlight.
Usage (Fig. A)

CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press variable speed trigger switch
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the
fastening torque is affected by many factors including
the following:
‑ Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
Accessory size: Failure to use the correct accessory
‑
size will cause a reduction in fastening torque.
Bolt size: Larger bolt diameters generally
‑
require higher fastening torque. Fastening torque
will also vary according to length, grade, and
torque coefficient.
‑ Bolt: Ensure that all threads are free of rust and
other debris to allow proper fastening torque.
Material: The type of material and surface finish of
‑
the material will affect fastening torque.
Fastening time: Longer fasten ing time results in
‑
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
located around the chuck
1 to start operation.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D WALT call 1-800-4-D
e
(1-800-433-9258) or visit our website: www.dewalt.com.
Impact Accessories

WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that they contain no cracks.
Belt Hook (Fig. A)

Optional Accessory


WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or
suspend objects from the belt hook. ONLY hang
tool's belt hook from a work belt.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook,
use only the screw 9 that is provided. Be sure to securely
tighten the screw.
The belt hook 8 can be be attached to either side of the
tool using only the screw 9 provided, to accommodate left-
or right- handed users. If the hook is not desired at all, it can
be removed from the tool.
To move belt hook, remove the screw
hook in place then reassemble on the opposite side. Be sure
to securely tighten the screw.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
•
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
•
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
English
WALT
e
WALT
e
9 that holds the belt
WALT factory
e
9