Tabla de contenido
Publicidad
TABLE OF CONTENTS
Safe ty Rules ..........................................2-4
Prod uct Spec i f i ca tions ..............................4
Assembly / Pre-Operation ........................5
Op er a tion.............................................6-10
Maintenance Sched ule ........................... 11
SAFETY RULES
IMPORTANT: This cutting machine is
capable of amputating hands and feet and
throwing objects. Failure to observe the
following safety instructions could result in
serious injury or death.
Look for this symbol to point out im por -
tant safety precautions. It means
CAU TION!!! BECOME ALERT!!!
YOUR SAFE TY IS INVOLVED.
WARNING: In order to prevent ac-
ci den tal starting when setting up, trans-
port ing, ad just ing or making repairs,
always dis con nect spark plug wire and
place wire where it can not come in contact
with plug.
WARNING: Engine exhaust, some of its
constituents, and certain vehicle com po nents
contain or emit chem i cals known to the State
of Cal i for nia to cause can cer and birth defects
or oth er re pro duc tive harm.
WARNING: Battery posts, terminals and
related accessories contain lead and lead
compounds, chemicals known to the State
of Cal i for nia to cause can cer and birth
defects or oth er re pro duc tive harm. Wash
hands after handling.
CAUTION: Muff er and other engine
parts become extremely hot during
operation and remain hot after engine
has stopped. To avoid severe burns on
contact, stay away from these areas.
Maintenance ...................................... 11-14
Ser vice and Ad just ments...................14-15
Stor age ..............................................16-17
Trou ble shoot ing .................................17-18
Re pair Parts.......................................36-43
Warranty .................................................44
I. GENERAL OPERATION
• Read, understand, and follow all
in struc tions on the machine and in the
manual(s) before starting. Be thor ough ly
familiar with the controls and the proper
use of the machine before starting.
• Do not put hands or feet near or under
rotating parts. Keep clear of the dis-
charge opening at all times.
• Only allow responsible individuals, who
are familiar with the in struc tions, to oper-
ate the machine.
• Clear the area of objects such as rocks,
toys, wire, bones, sticks, etc., which
could be picked up and thrown by blade.
• Be sure the area is clear of other people
before mowing. Stop ma chine if anyone
enters the area.
• Do not operate the mower when bare-
foot or wearing open sandals. Al ways
wear substantial foot wear.
• Do not pull mower backwards unless
absolutely nec es sary. Always look down
and behind before and while moving
backwards.
• Never direct discharged material toward
anyone. Avoid discharging material
against a wall or obstruction. Material
may richochet back toward the operator.
Stop the blade when crossing gravel
surfaces.
• Do not operate the mower without
proper guards, plates, grass catcher or
oth er safety protective devices in place.
• See manufacturer's instructions for prop-
er operation and installation of accesso-
ries. Only use accessories approved by
the manufacturer.
• Stop the blade(s) when crossing grav el
drives, walks, or roads.
• Stop the engine (motor) whenever you
leave the equip ment, before clean ing the
mower or unclogging the chute.
• Shut the engine (motor) off and wait until
the blade comes to complete stop before
removing grass catcher.
• Mow only in daylight or good artif cial
light.
2
HONDA 4-CYCLE ENGINE
FLYWHEEL
KEY PART
NO. NO.
DESCRIPTION
1
1240845 Grommet A, Rear Cover
2
0348433 Key, Special, Woodruff #25 x
18
4 5580659
Coil Assembly, Ignition
5
5580667 Flywheel Assembly
7 6869630
Arm, Governor
8 7229859
Rod, Governor
9
6315816 Cord, Stop Switch
10
5580683 Switch Assembly, Engine Stop
11
7526155 Holder, Wire
12
5580352 Spring, Throttle Return
13
7301591 Brake Sub-Assembly
14
2488187 Bolt, Flange #6 x 45 (CT200)
15
5580790 Spring, Brake Lever
16 2418671
Bolt, Governor Arm
17
0471623 Nut, Flange 6 mm
18
0803619 Bolt, Flange #6 x 14 (CT200)
19
1725050 Bolt, Flange #6 x 23 (CT200)
20
0442038 Nut, Special 14 mm
21
0485946 Screw, Washer Head #4x12
22
1510361 Washer, Plain 4 mm
CYLINDER BARREL
KEY PART
NO. NO.
DESCRIPTION
1
7809890 Barrel Assembly, Cylinder
3
5579990 Cover, Head
4
5580006 Cover Comp., Breather
5
0636845 Bolt, Flange #6 x 12 (CT200)
6
0803619 Bolt, Flange #6 x 14 (CT200)
7
5581038 Oil Seal 25A x 62 x 6
8
1441112 Plug, Spark (BPR6ES) (NGK)
PISTON / CONNECTING ROD
KEY PART
NO. NO.
DESCRIPTION
1
8571945 Piston
2
1426576 Pin, Piston
3
8270217 Rod Assembly, Connecting
4
1431055 Bolt, Connecting Rod
5
2605517 Clip, Piston Pin 13 mm
6
8571937 Ring Set, Piston (Teikoku)
MODEL NUMBER GCV160-LAS3A
CRANKSHAFT
KEY PART
NO. NO.
DESCRIPTION
3
5664495 Crankshaft Comp.
5
5581012 Washer, Thrust
OIL PAN
KEY PART
NO. NO.
DESCRIPTION
1
6771489 Pan Assembly, Oil
2
1452754 Gasket, Oil Filler cap
4
5664503 Extension, Oil Filler
5
5664511 Washer, Extension Lock
6
5716915 Gauge Assembly, Oil Level
8
6384341 Shaft, Governor Holder
9
6384333 Governor Assembly
10
5580287 Weight, Governor
11
5580295 Holder, Governor Weight
12
1427244 Pin, Governor Weight
13
1427251 Slider, Governor
14
5580303 Shaft, Governor Arm
15
0803619 Bolt, Flange #6 x 14 (CT200)
16
0748111 Bolt, Flange #6 x 25
18
2413862 Washer, Thrust 6 mm
19
2456697 Clip, Governor Holder
20
5581046 Oil Seal 28 x 41.25 x 6
22
1377704 ORing 14.8 x 2.4 (NOK)
23
0345900 Washer, Plain 6 mm
25
0115527 Pin, Lock 8 mm
26
1417369 Dowel Pin #8 x 20
MUFFLER
KEY PART
NO. NO.
DESCRIPTION
1
8213597 Kit, Spark Arrester
2 5580485
Muff er, Complete
3
7377062 Protector, Muff er
5 5656012
Spark Arrester
6 561
1397 Plate, Arrester Number
7
5737457 Gasket, Muff er
8
5580972 Bolt, Flange #6 x 79 (CT200)
9
0636845 Bolt, Flange #6 x 12 (CT200)
11
1431121 Screw, Tapping #4 x 6
43
Publicidad
Tabla de contenido
