Wiring Diagram; Replacement Parts - Eaton Champ CROUSE-HINDS Serie Manual Del Usuario

WIRING DIAGRAM

LOWER HOUSING
HEATSINK
G
GREEN/YELLOW
G
G
(GREEN/
YELLOW)
3 POLE SPLICE
CONNECTOR
DRIVER
(YELLOW/BLACK)
LED PCB 1
P4 +
LINE
NEUTRAL
POSITIVE
NEGATIVE
GROUND
CLASS I, DIV 2,
CLASS II, DIV 1,
GROUPS A, B, C, D
GROUPS E, F, G
105°
45°
60°
45° PAST VERTICAL 60° BEFORE VERTICAL
45° PASSÉ VERTICAL
60° AVANT VERTICAL
3. Re-install back cover/heat sink and tighten all nine (9) mounting screws to 22 in.-
lbs. (2.5 N-m). Be sure wires are not pinched during cover installation.
• Replace any damaged or missing cover screws. Use only stainless steel
#10-24 x 0.75"cover screws.
4. To make final vertical adjustment, loosen the pivot bolts on the floodlight yoke to
position floodlight at the desired angle. See Figure 3.
NOTE: Yoke mounting range is 45 degrees back to 60 degrees forward.
5. Rotate the floodlight housing to the desired position.
6. Tighten the two (2) 1/2-13 pivot bolts to 45 ft.-lbs. (61 N-m).
7. Tighten two (2) 5/16-18 angle marker bolts to 138 in.-lbs. (15.6 N-m).
8. Turn power on.
To avoid ignition of the hazardous atmospheres or overheating of the
floodlight:
Do not position the floodlight beyond the aiming range limits.
IF 1842 • 02/19
SUPPLY WIRE
N
L
BLACK
WHITE
(DC-)
(DC+)
N L
N
L
(WHITE)
(BLACK)
INPUT BLACK/WHITE
PURPLE (+)
GRAY (-)
OUTPUT
+ (RED)
- (BLUE)
2X
(YELLOW/RED)
2 POLE SPLICE
CONNECTOR
P1 -
60°
60° BEFORE VERTICAL
60° AVANT VERTICAL
Figure 3
WARNING
Copyright
2X
3 POLE SPLICE
CONNECTOR
3X 3 POLE SPLICE
CONNECTOR
3X
2 POLE SPLICE
CONNECTOR
Connection not used
Figure 2
PIVOT
1/2-13 BOLT
MAINTENANCE
LOOSEN BOLTS TO SET
FLOODLIGHT ANGLE
• Perform visual, electrical and mechanical inspections on a regular basis. The
environment and frequency of use should determine this. However, it is recommended
that checks be made at least once a year. We recommend an Electrical Preventive
5/16-18 ANGLE BOLT
Maintenance Program as described in the National Fire Protection Association Bulletin
NFPA 70B: Recommended Practice for Electrical Equipment Maintenance (www.nfpa.
org).
• The lens should be cleaned periodically to ensure continued lighting performance. To
clean, wipe the lens with a clean, damp cloth. If this is not sufficient, use a mild soap
or a liquid cleaner such as Collinite NCF or Duco #7. Do not use an abrasive, strong
alkaline or acid cleaner. Damage may result.
• Visually check for undue heating evidenced by discoloration of wires or other
components, damaged parts or leakage evidenced by water or corrosion in the interior.
Replace all worn, damaged or malfunctioning components and clean gasket seals before
putting the luminaire back into service.
• Electrically check to make sure that all connections are clean and tight.
• Mechanically check that all parts are properly assembled.

REPLACEMENT PARTS

Crouse-Hinds Champ LED Floodlights are designed to provide years of reliable lighting
performance. However, should the need for replacement parts arise, they are available
through your authorized Crouse-Hinds distributor. Assistance may also be obtained through
your local Crouse-Hinds Sales Representative or the Crouse-Hinds Sales Service Department,
1201 Wolf Street, Syracuse, New York 13208, Phone 866-764-5454.
2019, Eaton's Crouse-Hinds Division
®
HEATSINK
OPEN TERMINALS FOR THRU WIRING
FROM FIXTURE TO FIXTURE
GREEN/YELLOW
WHITE
(DC+)
G N
G
N
(GREEN/ (WHITE)
YELLOW)
DRIVER
OUTPUT
+ (RED)
- (BLUE)
(YELLOW/BLACK) (YELLOW/RED)
P1 -
LED PCB 1
P4 +
UPPER HOUSING
BLACK
3X
(DC-)
2 POLE SPLICE
CONNECTOR
L
L
(BLACK)
INPUT BLACK/WHITE
PURPLE (+)
GRAY (-)
Connection not used
2X
2 POLE SPLICE
CONNECTOR
Page 2