Antenna Installation - BFT ALPHA Instrucciones De Uso

Téléchargé sur www.confort-electrique.fr
ENGLISH
7-12 Closing limit switch (N.C.). If not used, leave the bridge con-
nected.
13-14 Output 24V~supply to photocells or other devices.
15-16 Output for gate-open warning light outputor alternatively 2nd
radio channel.
17-18 Antenna input for radio-receiver plug-in board (17 signal-18
braid).
JP3
19-20 Alpha: PEDESTRIAN input (N.O.)
Alpha BOM: PEDESTRIAN input (N.O.) with trimmer
TW=max.
CLOSE input (N.O.) with trimmer TW=min.
WARNING: the pedestrian function can be used provided that
limit switches are fitted.
JP4 Radio-receiver board connector, 1-2 channels.
Fig.7 shows a general wiring diagram.
5) LED (Fig.3)
The ALPHA-ALPHA BOM control units are provided with a series
of self-diagnosis LEDs which control all the functions.
DL1: Incorporated radio receiver LED
DL2: Alpha: comes on with the START command
Alpha BOM:
START (trimmer TW=max)-comes on with the START command
OPEN (trimmer TW=min)-comes on with the OPEN command
DL3: STOP - goes off when a STOP command is given.
DL4: PHOT - Photocell - goes off when the photocells are not aligned
or in the presence of obstacles.
DL5: SWO - Goes off when the opening limit switch is operated.
DL6: SWC - Goes off when the closing limit switch is operated.
6) DIP-SWITCH SELECTION (Fig.3)
DIP1)
TCA [ON] - Automatic closing time TCA.
ON: Activates automatic closing
OFF: Excludes automatic closing
DIP2)
FCH [ON] - Photocells.
ON: Photocells are only active in the closing phase.
OFF: Photocells are active both in the closing and opening phase.
DIP3)
BLI - Blocks impulses.
ON: START commands are not accepted during the opening phase.
OFF: START commands are accepted during the opening phase.
DIP4)
3P/4P - 3 Steps/4 Steps
ON: Enables 3-step logic.
OFF: Enables 4-step logic.
DIP5)
CODE FIX – Fixed code.
ON: Activates incorporated receiver in fixed code mode.
OFF: Activates incorporated receiver in rolling-code mode.
DIP6)
RADIO LEARN - Radio transmitter programming
ON: This enables transmitter storage via radio:
1 – First press the hidden key (P1) and then the normal key (T1,
T2, T3 or T4) of a transmitter already memorised in standard
mode by means of the radio menu.
2 – Within 10s press the hidden key (P1) and the normal key
(T1, T2, T3 or T4) of a transmitter to be memorised.
The receiver exits the programming mode after 10s, other new
transmitters can be entered before the end of this time.
This mode does not require access to the control panel.
OFF: This disables transmitter storage via radio.
are only memorised by means of manual programming.
DIP7)
SCA – Gate-open warning light or 2nd radio channel.
OFF: Activates relay output in Gate-open warning light mode.
ON: Activates relay output as 2nd radio channel.
DIP8)
10 -
ALPHA-ALPHA BOM - Ver. 06
Téléchargé sur www.confort-electrique.fr
Retrouvez tous les produits du fabricant BFT sur notre site internet www.confort-electrique.fr
INSTALLATION MANUAL
FAST CLOSE
ON: Closes the gate after photocell disengagement, before waiting
for the end of the TCA set.
OFF: Command not entered.
7) TRIMMER ADJUSTMENT (Fig.3)
TCA (Dip1 ON).
It is used to set the automatic closing time, after which the gate
closes automatically (adjustable from 0 to 90 s.).
TW
Alpha:
Alpha BOM: Working time is fixed to 10s.
trimmer TW = min: inputs 7-8 and 19-20 are considered as OPEN and
trimmer TW = max: inputs 7-8 and 19-20 are considered as START
8) INTEGRATED RECEIVER TECHNICAL SPECIFICATION
Receiver output channels:
- output channel 1, if activated, controls a START command
- output channel 2, if activated, controls the excitation of the 2nd
radio channel relay for 1s.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with

ANTENNA INSTALLATION

Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere
with radio reception. In case of insufficient transmitter range, move
the antenna to a more suitable position.
9) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means
of the Universal palmtop programmer
installations in the "collective receivers" mode, as well as manage
the complete installation database using the EEdbase software.
10) MANUAL PROGRAMMING
In the case of standard installations where no advanced functions
are required, it is possible to proceed to manual storage of the
transmitters
1) If you wish the transmitter T key to be memorised as Start, press
thSW1 button on the control unit, otherwise if you wish the transmitter
key to be memorise as second radio channel, press the SW2 button
on the control unit.
2) When the DL1 LED blinks, press the transmitter P1 hidden key,
and the DL1 LED will stay on permanently.
3) Press the key to be memorised on the transmitter, LED DL1 will
start blinking again.
4) To memorise another transmitter, repeat steps 2) and 3).
5) To exit the storage mode, wait until the LED is switched off com-
pletely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO
THE FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the
key code to the receiver; this code is necessary in order to carry out
subsequent cloning of the radio transmitters.
10.1) CONTROL UNIT MEMORY CANCELLATION
The transmitters In order to cancel the control unit memory completely, simultaneously
press for 10 seconds the SW1 and SW2 buttons on the control unit
(DL1 LED blinking). Correct memory cancellation will be indicated
by the DL1 LED staying on permanently. To exit the storage mode,
wait until the LED is switched off completely.
Retrouvez tous les produits du fabricant BFT sur notre site internet www.confort-electrique.fr
Sets the motor working time (from 0 to 90s), after
which the motors stop.
In the case where electrical limit switches are used,
add a few extra seconds after the gate leaf stopping
time.
CLOSE inputs respectively.
and PEDESTRIAN inputs respectively.
which allows you to create
.