Grohe Chiara 19 410 Manual Del Usuario página 5

GB
Installation
Always take care with the concealed
mixer housing, see fold-out page I.
- Plaster and tile the wall, excluding the area occupied by the
mounting template. Seal any apertures in the wall so that
they are watertight to spray water.
• Tiles laid in mortar should be pointed so that the joint
is tapered towards the outside.
• Seal prefabricated walls with a permanently plastic
compound.
Central thermostat mixer
Installation, see fold-out page II, Figs. [1], [2a] and [10], [11].
1. Remove the mounting template, see fig. [1].
2. Install sleeve (A), see Fig. [2a].
3. Grease seals (B1) of escutcheon mounting base (B2) with
the special grease supplied, push on escutcheon mounting
base (B2) and fasten with screws (C).
4. Attach escutcheon (B).
Adjustment and installing the temperature control
Adjusting
handle (W), see section
Shower thermostat
Installation of functional elements, see fold-out page II,
Figs. [1] to [4].
Shut off cold and hot water supplies.
1. Remove the mounting template, see fold-out page I, Fig. [1].
2. Unscrew closure plug (D) and plug (C), see Fig. [2b].
3. Screw in sound absorber (F), see Fig. [3].
4. Install race (G); there is only one possible position,
see detail, Fig. [3].
5. Grease O-ring of adapter (H) with the special
grease supplied. Fasten adapter (H), see Fig. [4].
6. Screw in ceramic headpart (I).
Open cold and hot-water supply and check
connections for water-tightness.
Installation of escutcheon (M) and shut-off handle (R)
and adjustment of the economy stop (O), see fold-out
page II, Figs. [5] to [9].
1. Attach sleeve (J), holder (K) and sleeve (L), see Fig. [5].
2. Grease seals (M1) of escutcheon mounting base (M2) with
the special grease supplied, push on escutcheon mounting
base (M2) and fasten with screws (N), see Fig. [6]
3. Attach escutcheon (M).
• The flow rate is limited by the economy stop (O) provided,
see Fig. [7].
To install the shut-off handle, proceed as follows:
1. Close the ceramic headpart (I) by turning clockwise.
2. Install the economy stop (O) in the desired position.
For adjustment range, see Fig. [8].
3. Fit splined adapter (Q), see Fig. [9].
4. Fit shut-off handle (R) so that the button (R1) is at the top.
5. Install in screw (S).
6. Attach cap (T).
If a higher flow rate is desired, the stop can be overridden
by pressing the button (R1).
If the thermostat has been installed at too great a depth,
this can be increased by 27.5mm with an extension set
(see Replacement parts, fold-out page I, Prod. no.: 47 780).
Reversed connection (hot on right - cold on left).
Replace thermostatic compact cartridge (Z), see Replacement
parts, fold-out page I, Prod. no.: 47 186 (3/4").
Adjusting
Installation of the temperature control handle (W)
and temperature adjustment, see fold-out page II,
Figs. [10] and [11].
• Before the mixer is put into service, if the mixed water
temperature measured at the point of discharge varies
from the specified temperature set on the thermostat.
• After any maintenance operation on the thermostatic
cartridge.
1. Open the shut-off valve and check the temperature
of the water with a thermometer, see Fig. [10].
2. Turn the regulating nut (U) clockwise or anti-clockwise until
the water temperature reaches 38 °C.
3. Insert slide ring (V) in groove (V1).
4. Fit stop (U1) in guide (U2), see Fig. [11].
5. Install temperature control handle (W) so that
the button (W1) is at the top.
6. Install screw (X).
.
7. Attach cap (Y).
Temperature limitation
The safety stop limits the temperature range to 38 °C.
If a higher temperature is desired, the 38 °C limit can
be overridden by pressing button (W1), see Fig. [11].
Prevention of frost damage
When the domestic water system is drained, thermostats must
be drained separately, since non-return valves are installed
in the hot and cold water connections.
The complete thermostat assemblies and non-return
valves must be unscrewed and removed.
Maintenance
Inspect and clean all parts, replace as necessary and lubricate
with special grease.
Shut off cold and hot water supplies.
I. Thermostatic compact cartridge (Z), see fold-out page III,
Figs. [12], [13] and [14].
• Loosen screw ring (AB) using a 34mm tool.
• If necessary, lever out thermostatic compact cartridge (Z)
via recess (Z1).
• Remove screw ring (AB).
Assemble in reverse order.
Observe the correct installation position of the
thermostatic compact cartridge (Z), see detail (Z2).
Readjustment is necessary after every maintenance operation
on the thermostatic cartridge (see Adjusting).
II. Non-return valve (AC), see fold-out page III,
Figs. [12], [13] and [15].
Assemble in reverse order.
III. Ceramic headpart (I), see fold-out page III,
Figs. [12], [13] and [15].
Assemble in reverse order.
Observe the correct installation positions.
Replacement parts, see fold-out page I
(* = special accessories).
Care
For directions on the care of this fitting, refer to the
accompanying Care Instructions.
2