Tools Of The Trade; End Panel Layouts; Power Inputs/Speaker Outputs - Polk Audio PA D4000.4 El Manual Del Propietario

SUB
INT REMOTE LEVEL CONTROL
SUB
LEVEL SONIC LPF

TOOLS OF THE TrAdE

SUB INT
SOURCE
INPUT
6V 200mV 20Hz 38Hz 40Hz 220Hz
Listed next are the majority of the tools required to perform an installation . Having the proper tools will make
REAR FRONT
SOURCE
HPF
1
CHANNEL
HPF FULL BPF
the installation that much easier . MODE
6V 200mV
SUB 1
REAR
40Hz 4000Hz 6V 200mV 80Hz 4000Hz 40Hz 400Hz 6V 200mV
• Phillips head screwdriver FULL HPF
HPF LEVEL LPF HPF LEVEL
4CH ST
• Electric drill and 3/16" and 1/8" drill bits • Safety glasses
40Hz 4000Hz
SUB 2
• Permanent ink marker or pencil
9 10 11 12 13 14 15 16
• Safety glasses
9
• Wire strippers and cutters
• Electrical tape
• Amplifier Power Wire

ENd PANEL LAyOuTS

PA d4000.4 Line Level Inputs/Controls
3 4a 5a 9a 10a
2 3 4a
X-OVER X-OVER
FREQ x 1 FREQ x 1
FREQ x 10 FREQ x 10
L
HPF LPF FULL FULL LPF HPF
BPF HPF 4CH ST BPF HPF
1
LEVEL HPF
20Hz 400Hz 50Hz 500Hz 50Hz 500Hz 20Hz 400Hz
CHANNEL
R
REAR FRONT
MODE
6V 200mV 20Hz 400Hz
REAR
4b 5b 6 7 8 9b 10b
4b
1. Status LEds (on top of amplifier): Power and Protection—Power will illuminate to indicate
the amplifier is on and operating normally; protection will illuminate if the amplifier shuts down
due to short circuit, DC offset, or overheating detected by onboard protection circuitry .
rear Controls
2. rear Line Level Inputs—accepts line level input from the rear channels of a head unit .
3a 3b 4a 4b 5
3. rear Level Control—Adjusts the gain of the rear channels to match the output voltage
2 3a
from your head unit .
4. (a) rear High-Pass Frequency Button—When FREQ x 10 is engaged, the crossover's
INPUT
range increases to 200Hz - 4kHz .
LPF HPF L
(b) rear HPF Control—Adjusts the high pass filter frequency to attenuate frequencies
X-OVER X-OVER
below the setting on the control .
FREQ x 1 FREQ x 1
LPF HPF LEVEL
1
5. (a) rear Low-Pass Frequency Button—When FREQ x 10 is engaged, the crossover's R
FREQ x 1
HPF
FULL BPF
50Hz 500Hz 20Hz 400Hz 6V 200mV
range increases to 500Hz - 5kHz .
FREQ x 10 FREQ x 10
(b) rear LPF Control—Adjusts the low pass filter frequency to attenuate frequencies
FREQ x 10
above the setting on the control .
6. rear BPF, FuLL, HPF Switch— Selects full range, high pass filter, or band-pass filter . The BPF setting
allows you to use both the high pass filter and low pass filter, and it is for use with mid-range drivers .
The FULL setting does not attenuate any frequencies and is for full range speaker systems . The HPF
setting attenuates low frequencies and is used with mid-range speakers and tweeters .
7. Channel mode Switch (ST/4Ch)—Set the switch to 4CH if you are using four channel outputs from your head
unit to the FL, FR, RL, RR inputs on the amplifier . Set the switch to ST (stereo) mode if you are using two channel
outputs from your head unit . In the ST position, the amplifier will take the signal input to the FL and FR inputs
2 3 4 5 6
and send the same signals also to the RL and RR amplifier channels .
2
8. Front BPF, FuLL, HPF Switch—Selects full range, high pass filter, or band-pass filter . The BPF
setting allows you to use both the high pass filter and low pass filter, and it is for use with mid-range
drivers . The FULL setting does not attenuate any frequencies and is for full range speaker systems .
The HPF setting attenuates low frequencies and is used with mid-range speakers and tweeters .
4
1
INPUT
FL RL
SUB
INPUT
REMOTE LEVEL CONTROL FL
SUB
LEVEL SONIC LPF
PA D5000.5
20Hz 38Hz 40Hz 220Hz
FRONT
HPF
CHANNEL
• Solderless, crimp-on connectors and a crimping tool BPF
FR RR FULL
MODE
6V 200mV 80Hz 4000Hz 40Hz 400Hz 6V 200mV
FR
HPF LEVEL LPF HPF LEVEL
4CH ST
• DMM or VOM
• Nylon tie straps
10 11 12 13 14 15 16
• Wire crimper
• Grommets for passing wires through metal car walls
11 12
5a 9a 10a 11
L
X-OVER X-OVER
PA D4000.4
FREQ x 1 FREQ x 1
LEVEL
FREQ x 10 FREQ x 10
R
LPF FULL FULL LPF HPF LEVEL
BPF HPF 4CH ST BPF HPF
6V 200mV
50Hz 500Hz 50Hz 500Hz 20Hz 400Hz 6V 200mV
CHANNEL
FRONT
MODE
5b 6 7 8 9b 10b
6 7
3b 4a 4b 5 6
OUTPUT
L
INPUT OUTPUT
PA D2000.2
LPF HPF
L
X-OVER X-OVER
R
FREQ x 1
LPF HPF LEVEL
R
50Hz 500Hz 20Hz 400Hz 6V 200mV
FREQ x 10
7 8
3 4 5 6 7
PA D1000.1
© 2011 Polk Audio—all rights reserved
9. (a) Front Low-Pass Frequency Button—When FREQ x 10 is engaged, the crossover's
RL
(b) Front LPF Control—Adjusts the low pass filter frequency to attenuate frequencies
GND
PA D5000.5
10 (a) Front High-Pass Frequency Button—When FREQ x 10 is engaged, the crossover's
RR
(b) Front HPF Control— Adjusts the high pass filter frequency to attenuate frequencies
11. Front Level Control—Adjusts the gain of the front channels to match the output voltage
from your head unit .
12. Front Line Level Inputs—Accepts line level input from the front channels of a head unit .
PA d4000.4 Power Inputs/Speaker Outputs
12
L
PA D4000.4
R
1. gNd (ground)—Connect this terminal directly to the metal chassis of the vehicle, using the shortest
wire necessary to make this connection. Always use wire of the same gauge or larger than the +12V power
wire . The chassis connection point should be scraped free of paint and dirt . Use only quality crimped and/or
soldered connectors at both ends of this wire . DO NOT connect this terminal directly to the vehicle battery
ground terminal or any other factory ground points .
2. rEm (remote Turn On)—This terminal turns on the amplifier when +12V is applied to it.
Connect it to the remote turn on lead of the head unit .
3. +12V Power—Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal
of the vehicle battery or the positive terminal of an isolated audio system battery .
WArNINg: Always protect this power wire by installing a fuse or circuit breaker of the appropriate
size within 12" of the battery terminal connection.
7
4. Fuse—These fuses (40A & 35A) protect the amplifier against internal electrical damage and are meant
to protect only the amplifier . All other power connections should be fused at the power source .
5. Speaker Output—Connect the speakers here
6. Terminal Adaptor—The adaptor enables the use of cable up to 0000AWG
L
for the ground and +12V connections (see illustration below).
GND
PA D2000.2
R
8
© 2011 Polk Audio—all rights reserved
PA D1000.1
SUB RL
range increases to 500Hz - 5kHz .
REM 12V
above the setting on the control .
40A 40A
SUB RL
GND REM
range increases to 200Hz - 4kHz .
below the setting on the control .
1 2 3 4
1
RL RR
GND REM 12V
40A 35A
RL RR
GND
1 2 3 4
1
REM 12V
25A 25A L
GND REM
1 2 3 4
1
RR FL FR
SUB RL RR FL
RR FL FR
12V
40A 40A
SUB RL RR FL
5
2 3 4 5
FL FR
RL RR FL
FL FR
REM 12V
40A 35A
RL RR FL
5
2 3 4 5
BRIDGED
BRIDGED
L R R
12V
25A 25A L L
6. Terminal Adaptor
5
2 3 4 5
FR
FR
FR
FR
R R
5