Bosch GCM 350-254 Professional Manual Original página 34

34 | English
Sliding mitre saw
Laser class
Divergence of laser line
Weight according to EPTA-
Procedure 01:2014
Protection class
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Max. cutting width
Hole diameter
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-
specific models.
Permissible Workpiece Dimensions (see "Permissible workpiece dimensions", page 38)
Noise Information
Noise emission values determined according to
EN 62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 95 dB(A); sound power level
106 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items Included
See the list of items included at the start of
the operating manual.
1 609 92A 5UA | (06.10.2020)
GCM 350-254 GCM 350-254
1
1.0 mrad
(full angle) (full angle)
kg 24.2
/ II
mm 254
mm 1.7–2.6
mm 3.2
mm 30
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with fitted saw blade (47)
– Screw clamp (38)
– Hex key
– Hex key (60)
– SDS bolt (30)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Ring spanner or open-ended spanner (size: 10 mm)
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure A1−A2)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (17) are used for this pur-
pose.
or
– Firmly clamp the base of the power tool to the work sur-
face with commercially available screw clamps.
Mounting on a Bosch saw stand
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
GCM 350-254
1 1
1.0 mrad 1.0 mrad
(full angle)
24.2 24.2
/ II / II
254 254
1.7–2.6 1.7–2.6
3.2 3.2
25.4 30
GCM 350-254
1
1.0 mrad
(full angle)
24.2
/ II
254
1.7–2.6
3.2
25.4
Bosch Power Tools