Yamaha A-S3200 Folleto De Seguridad página 4

Handling caution
• Do not touch the surface having this
label. Doing so may cause burns. The
label on the device indicates that the
surface to which the label is attached
may become hot during operation.
• Do not insert foreign materials such as metal or paper
into the openings of this unit. Failure to observe this
may cause a fire, electric shocks, or malfunctions.
• Keep small parts out of the reach of infants. Your
children may accidentally swallow them.
• Do not do the following:
- Stand on or sit on the equipment.
- Put heavy items on top of the equipment.
- Place the equipment in a stack.
- Apply unreasonable force to buttons, switches,
input/output terminals, etc.
Failure to observe this may cause injuries or damage
to the equipment.
• Avoid pulling the connected cables to prevent injuries
or damage to the unit by causing it to fall.
Battery use
• Do not use batteries other than specified batteries.
Doing so may cause fire or burns, or result in fluid
leakage that may cause skin inflammation.
• Do not use new batteries together with old ones.
Using new ones with old ones could cause a fire,
burns, or inflammation due to fluid leaks.
• Do not mix battery types, such as alkaline batteries
with manganese batteries, or batteries from different
makers, or different types of batteries from the same
maker, since this can cause a fire, burns, or
inflammation due to fluid leaks.
• Keep batteries away from children. A child could
accidentally swallow a battery. Failure to observe this
may also cause inflammation due to battery fluid
leaks.
• Do not put in a pocket or bag, carry, or store batteries
together with pieces of metal. The battery could short,
burst, or leak, causing a fire or injury.
• Always make sure all batteries are inserted in
conformity with the +/− polarity markings. Failure to
do so might result in a fire, burns, or inflammation due
to fluid leaks.
• When the batteries run out, or if the unit is not to be
used for a long time, remove the batteries from the
remote control to prevent possible leakage of the
battery fluid.
• When storing or discarding batteries, insulate the
terminal area by applying tape, or some other
protection. Mixing them with other batteries or metal
objects can cause a fire, burns, or inflammation due
to fluid.
4
NOTICE
Indicates points that you must observe in order to
prevent product failure, damage or malfunction
and data loss.
Power supply
• If not using the unit for a long period of time, be sure
to pull the power plug from the outlet.
Even if you place the unit in standby mode by
A
pressing the AMP (Standby/On) key on the remote
control, a small amount of current still flows through
the unit.
Installation
• Do not use this unit in the vicinity of other electronic
equipment, such as a TV, radio, or mobile phone.
Failure to observe this may cause this unit or the TV or
radio to produce noise.
• Do not use this unit in a location that becomes
extremely hot (such as near a heater) or extremely
cold; that is exposed to direct sunlight; or that is
subject to excessive dust or vibration. Failure to
observe these precautions may cause the unit's panel
to become deformed, the internal components to
malfunction, or the operation of the unit to become
unstable.
Connections
• If connecting external units, be sure to thoroughly
read the manual for each unit and connect them in
accordance with the instructions.
Failure to properly handle a unit in accordance with
the instructions could cause malfunctions.
Handling
• Do not place vinyl, plastic, or rubber products on this
unit. Failure to observe this may cause discoloration
or deformation in the panel of this unit.
• If the ambient temperature changes drastically (such
as during unit transportation or under rapid heating or
cooling) and there is a chance condensation may
have formed in the unit, leave the unit for several
hours without turning on the power until it is
completely dry before use. Using the unit while there
is condensation can cause malfunctions.
Maintenance
• If the temperature or humidity changes drastically,
water droplets (condensation) may form on the unit
surface. If water droplets form, immediately wipe
them off with a soft cloth. If water droplets are left on
the unit, they may be absorbed into the wooden parts,
causing deformation.
• When cleaning the unit, use a dry, soft cloth. Using
chemicals such as benzine or thinner, cleaning
agents, or chemical scrubbing cloths can cause
discoloration or deformation.