MSW Motor Technics MSW-SH-260 Manual De Instrucciones página 5

EN
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The product is intended to assist in guiding a long, heavy
workpiece into the machine tool. The product is intended
for home use only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
MSW-SH-260
10 11
9
1
8
7
6
1. Working frame
2. Handles
3. Upper leg
4. Lower leg (adjustable)
5. Left foot
6. Right foot
7. Crossbar to stabilize the legs
8. Leg adjustment lock
9. Anti-skid stop – small
10. Anti-skid stop - large
11. Transport handle
MSW-SH-200
1
2
3
4
10
9
7
8
6
5
11
8
1. Movable clamping jaw
2. Fixed clamping jaw
3. Working frame
4. Locking / unlocking latch
5. Clamp pedal
6. Front leg
7. Rear leg
8. Pedal release
9. Front leg locking button
10. Rear leg locking button
11. Front leg foot
3.2. PREPARING FOR USE
APPLIANCE LOCATION
Keep the device away from any hot surfaces. The appliance
should be used out of reach of children and people with
reduced mental and sensory functions.
ASSEMBLING THE APPLIANCE
2
MSW-SH-260
Take the appliance out of the packaging by the transport
handle, then slide out and unfold the legs (3 + 4) located
3
at the bottom of the frame. Press the adjustment lock of
the individual leg (8) to adjust the height of the working
frame (1) to your own needs and to the ground on which the
appliance will be used. Anti-slip stops (9 + 10) stabilize the
4
workpiece placed on the top of the working frame (1) when
it is being machined. The tool can also be used as a base for
a quick construction of a temporary work table - all you need
to do is put a stable plate on it. A plate that is to serve as
5
e.g. a work table can be additionally reinforced by inserting
two crossbars in the "U" (2) holders of the working frame (1).
MSW-SH-200
Take the appliance out of the packaging and remove all the
protective pieces.
C
B
A
1
D
D
A
E
B
E
C
2
Rev. 19.02.2021
D
E
D
E
3
B
A
4
• Place the working frame on the floor with the legs
facing up (see fig. 1).
• Loosen the locking knob (A) on the back of the frame
(Fig. 1)
• Pull the rear base (B) out of the locking slot (C).
• Slightly lift up and tilt the base (A) backwards (Fig.
2). Lift the base to an upright position. Place the rear
base in the frame opening (B) and tighten the locking
knob (C).
• Lift the two front legs (D) (Fig. 2) and lock them with
the locking buttons (E). Turn the locking knobs half
a turn until they are tightened on the frame (see fig.
3.)
• Place the stand upright on its legs.
• Lower the clamping pedal (A) (Fig. 4) and pull it
towards the front of the stand until it clicks into place.
DISMANTLING THE STAND:
• Place the top of the stand on the floor with the legs up
(see fig. 1).
• To release and fold down the clamping pedal (A) (Fig.
4), simply press the trigger (B).
• To fold the legs, proceed in the reverse order (see
ASSEMBLY OF THE DEVICE above)
3.3. DEVICE USE
3.3.1. CLAMPING A WORKPIECE
C B
D
A
A
5
Rev. 19.02.2021
EN
B
A
B
6
• Set the locking / unlocking latch (A) to the unlocked
position by sliding it upwards (see fig. 5.)
• Open the jaws by pushing the sliding jaw (B) (Fig. 5)
away from the fixed jaw (C).
• Place the piece to be machined (D) (fig. 5) between
the fixed jaw and the clamping jaw so that its length /
weight is equally distributed on both sides of the stand.
• Bring the sliding jaw (B) close to the workpiece, or
press the clamping pedal (A) several times so that the
jaw presses itself against the workpiece.
• To lock the sliding jaw (B) on the workpiece, set the
locking latch (B) to the locked position (fig. 6), by
sliding it downwards. Press the clamping pedal (A)
several times until the workpiece is completely locked
(fig. 6)
3.3.2. CLAMPING A LARGE WORKPIECE
B
A
A
8
A
9
A
10
9