KRATOS SAFETY EASYSAFEWAY 1 Manual página 16

"acceptance" of this installation. This person must check, among other things: suitability of the structural anchors and the receiving structure;
the installation plan relative to the job to be performed; cross-compatibility between the products (mounting bracket, adaptation plate and fall
arrest system installed on this anchorage).
If necessary and/or possible depending on the configuration of the site, we recommend placing barriers around the work area to secure and mark out
the area.
ACCESSORIES COMPATIBLE WITH EASYSAFEWAY 1:
+ RETRACTABLE FALL ARRESTER
FA 60 105 00
FA 60 105 07
Warning! Pay particular attention to properly installing the safety pins, and, if applicable, the pins used to mount the adaptation plate. If
applicable, make sure that the retractable fall arrester and/or winch are properly mounted. Do not use EASYSAFEWAY 1 if a single pin is
missing!
Warning! When in use, if another person stays near the davit arm (if handling or in the event that a rescue operation becomes necessary), this
spotter must ensure that he/she is not in situation that presents a fall risk. If the H-base is used, this third party can connect themselves the
anchorage rings on the mast. When using the brackets (FA 60 022 X1 & FA 60 022 X2) they are equipped with an anchorage point that allows
the third party present to be connected to a reliable anchorage in order to be secured.
Connections between the anchorage points and the fall arrest system or rescue system, affixed above, must be made using a connector (EN 362).
EASYSAFEWAY 1 is PPE; we recommended that it be allocated to a single user. However, another person is needed in the event of rescue operations.
User safety relies on the ongoing effectiveness of the equipment and full understanding of the safety instructions contained in this leaflet. The readability
of the product's markings must be checked regularly.
EASYSAFEWAY 1 must be positioned so that the anchorage is above the user (minimum strength 12 kN). Ensure that the general set-up limits swinging
in the event of a fall (the user should be plumb with the lifting arm as much as possible), and that the work is performed in such a way as to limit the risk
and height of a fall. It is important to check the free space under the user's feet depending on the system used.
Before and during use, we recommend that you make the necessary arrangements for a safe rescue, should this be required. If a motionless victim
remains suspended in a harness for more than 20 minutes, serious, potentially life-threatening, consequences can result (harness hang syndrome). Be
aware of the hazards that could reduce the performance of your equipment and, therefore, the safety of the user in the case of: exposure to extreme
temperatures (< -30°C or >50°C); prolonged exposure to the elements (UV rays, moisture) or to chemicals; electrical constraints; the fall arrest system
becoming twisted when in use; or sharp edges, friction, cuts, etc.
This equipment must only be used by trained, competent and healthy individuals or under the supervision of a trained and competent individual.
Warning! Certain medical conditions may affect user safety; if in doubt, consult your doctor.
Before each use, check: On the H-base (3 pieces): no deformation, cracks, dents or traces of oxidation. Check the presence of the locking pins (x4), that
they are in good working order and the presence of the captive cables. Check that the locking screws (x4) are present and in good working order. Check
that the adjustable feet (x4) are present and in good working order. Check that the castors (x4) are present, in good working order and locked. None of
these elements should show any traces of oxidation.
On the mast: no deformation, cracks, dents or traces of oxidation. Check the presence of the locking pins (x2), that they are in good working order and
the presence of the captive cables. Check carefully that all 3 anchorages are present and in good working order. None of these elements should show any
signs of oxidation, cracks or lack of material.
On the arm: no deformation, cracks, dents or traces of oxidation. Check carefully that the anchorage is present and in good working order. Check the
condition of the pulleys (x2), that they are in good working order, and in particular the wear; no sharp edges on the pulleys. None of these elements
should show any signs of oxidation.
Refer to the inspection recommendations for each system used in combination with the EASYSAFEWAY 1.
Do not remove, add or replace any of the product's components.
Chemicals: do not use the device in the event of contact with chemicals, solvents or fuels that could affect its operation.
TECHNICAL SPECIFICATIONS:
H-base, mast and arm, pin: aluminium; anchorage eye, pulleys: STAINLESS STEEL; adjustable support feet, locking screws and other hardware: steel.
Weight: FA 60 105 00 = 62 kg / FA 60 105 07 = 58.35 kg (H-base = 35 kg; Mast: FA 60 105 03 = 16 kg / FA 60 105 04 = 12.35 kg; Arm = 11 kg)
Use between: -30°C / +60°C
Resistance > 12 kN; Breaking strength > 23 kN.
KRATOS SAFETY certifies that EASYSAFEWAY 1 has been tested in accordance with standard EN 795:2012 Type A and B.
COMPATIBILITY FOR USE:
A harness must be used as part of a fall arrest system as defined in the product data sheet (EN 363) with the goal of guaranteeing that the dynamic force
exerted on the user during arrest of a fall is no greater than 6 kN. A fall arrest harness (EN 361) is the only body-support device that may be used. It can
be dangerous to create one's own fall arrest system in which each safety function can interfere with another safety function. Therefore, it is important to
read the recommendations on using each component in the system before use.
INSPECTION:
While the recommended service life of the product is unlimited (in accordance with the annual examination by a competent person authorised by
KRATOS SAFETY), it may be reduced according to use and/or the results of the annual inspections. The equipment must be systematically checked if
in doubt or after a fall and at least every twelve months by the manufacturer or a competent person* and in strict compliance with the manufacturer's
periodic examination procedures (and in particular the Inspection Guides ref. GI XX-3XXXXXX-XX), in order to ensure its strength and therefore the
safety of the user. The product data sheet should be completed (in writing) after each verification. The date of inspection and date of the next inspection
must be indicated on the data sheet. It is also recommended to put the date of the next inspection on the product.
*: refer to the definition of a competent person on our website under: Info/Technical Advice
If EASYSAFEWAY 1 is used to lift loads, the checks must be carried out every 6 months.
MAINTENANCE AND STORAGE: (These instructions must be strictly observed)
During transportation, keep the equipment away from any cutting edges and keep it in its packaging. Clean with water, wipe with a cloth and store in
a ventilated room to dry naturally, ensuring that it is away from any direct light or source of heat; the same applies for elements that may have got wet
during use. The system must be stored in its packaging in a cool, dry and ventilated room.
MOUNTING BRACKETS
FA 60 105 01 + FA 20 401 XX
MOUNTING BRACKETS
+ WINCH
FA 60 105 02 + FA 60 003 XX
16
OTHER ACCESSORIES
N/A