Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EXTENSION CORDS
Use proper extension cords. Make sure
your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug
and matching receptacle which will accept the
machine's plug. When using an extension cord, be sure
to use one heavy enough to carry the current of the
machine. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating. Fig.
D shows the correct gauge to use depending on the
cord length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
FOREWORD
Porter-Cable Model 3807 is a high capacity 10" compound miter saw designed to cut wood and non-ferrous metals. It can
crosscut 11-1/2" x 3-3/16" and 9" x 3-7/8", miter at 45° both left and right 8-1/8" x 3-3/16", and 6-3/8" x 3-7/8", bevel at 45°
left 11-1/2" x 2-3/16" and 8-1/2" x 2-5/8", compound 45° left miter and 45° bevel 8-1/8" x 2-3/16" and 6-1/2" x 2-5/8" and
compound 45° right miter and bevel 8-1/8" x 1-7/8" and 3-1/2" x 2-5/8".
NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations
contained in the manual are representative only and may not depict the actual color, labeling, or accessories,
and are intended to illustrate technique only.
1.
Miter Saw
2.
Work Clamp
UNPACKING AND CLEANING
1. Carefully remove the machine from the carton. Retain all packing materials until you have inspected and
satisfactorily operated the machine.
Do not operate this machine until you read and understand the entire instruction manual.
2. Place the machine on a firm, level surface with extra room for handling and proper support of the workpiece.
3. Familiarize yourself with all features and controls explained in this manual.
4. The machine is shipped with the cuttinghead locked in the down position and the table rotated to 45° left, Fig. 3.
To release the head and move it to the operating position, see "MOVING CUTTINGHEAD TO THE UP POSITION"
and "MOVING THE TABLE TO THE 0° CUT-OFF POSITION" in this manual.
All manuals and user guides at all-guides.com
FUNCTIONAL DESCRIPTION
CARTON CONTENTS
2
1
Fig. 1
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Volts
0-6
120
0-6
120
0-6
120
0-6
120
6-10
120
6-10
120
6-10
120
6-10
120
10-12
120
10-12
120
10-12
120
10-12
120
12-16
120
12-16
120
12-16
120
3
7
3.
Dust Elbow
4.
Arbor Wrench
5.
7/16'' Wrench
7
Total Length
Gauge of
of Cord in Feet
Extension Cord
up to 25
18 AWG
25-50
16 AWG
50-100
16 AWG
100-150
14 AWG
up to 25
18 AWG
25-50
16 AWG
50-100
14 AWG
100-150
12 AWG
up to 25
16 AWG
25-50
16 AWG
50-100
14 AWG
100-150
12 AWG
up to 25
14 AWG
25-50
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. D
4
5
6
Fig. 2
6.
1/2" x 7/16" Wrench
7.
Dust Bag
Publicidad
Tabla de contenido
