DeWalt DWE46103 Manual De Instrucciones página 10

English
Fig. H
Slider Switch (Fig. A)

CAUTION: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete
stop be fore laying the tool down.
nOTE: To reduce unexpected tool movement, do not
switch the tool on or off while under load conditions. Allow
the grinder to run up to full speed before touching the work
surface. Lift the tool from the surface before turning the tool
off. Allow the tool to stop rotating before putting it down.

WARNING: Before connecting the tool to a power
supply, be sure the slider switch is in the off position
by pressing the rear part of the switch and releasing.
Ensure the slider switch is in the off position as
described above after any interruption in power
supply to the tool, such as the activation of a ground
fault interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure. If the slider
switch is locked on when the power is connected, the
tool will start unexpectedly.
To start the tool, slide the ON/OFF slider switch
the front of the tool using the rear portion of the switch. To
stop the tool, release the ON/OFF slider switch.
For continuous operation, slide the switch toward the front
of the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press
the rear part of the slider switch and release.
Spindle Lock (Fig. A)
The spindle lock 2 is provided to prevent the spindle from
rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged
from the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do not
engage the spindle lock while the tool is operating. Damage
to the tool will result and attached accessory may spin off
possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
8
Tuckpointing and Cutting Application
13
(Fig. H)
1. Set the desired depth of cut, see Depth of Cut
Adjustment under Assembly and Adjustments.
2. Allow the tool to reach full speed before touching it to
the work surface.
3. Position yourself so the open underside of the shroud
and the wheel are facing away from you.
4. Place the edge
begin cut by plunging into the work surface.
nOTE: Keep the edge
work surface to ensure proper dust collection.
5. With the shroud oriented as shown in Figure F, move
the grinder right to left along the work surface. For the
best results the grinder should be positioned at a 45°
angle to the dust port when tuckpointing/cutting.
6. Remove the tool from work surface before turning off
the tool. Allow the tool to stop rotating before laying
it down.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
6 toward
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
13 of shroud onto the work surface and
13 of the shroud against the
WALT, have not been tested with this
e
WALT Industrial
e
WALT
e