Intended Use; Assembly And Adjustments - DeWalt DWE46103 Manual De Instrucciones

IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

Your tuckpoint grinder has been designed for professional
tuckpoint masonry applications. It is not intended for use
with metal or wood.
Using the tuckpoint grinder and shroud with appropriate
wheel and dust extractor vacuum will remove the vast
majority of static and airborne dust. This dust could
otherwise contaminate the working environment or pose
an increased health risk to the operator and those in
close proximity.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
The tuckpoint grinder is a professional tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Features
E-switch Protection™
The ON/OFF trigger switch has a no-volt release function.
In the event of a power outage or other unexpected shut
down, the trigger switch will need to be cycled (turned off
and then back on) to restart tool.
E-Clutch™
This unit is equipped with an E-Clutch™ (Electronic Clutch),
which in the event of a high-load or wheel pinch, the unit
will be shut off to reduce the reaction torque to the user.
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
WALT tools are factory tested;
e
The switch needs to be cycled (turned off and then back on)
to restart tool.
Power-OFF™ Overload Protection
The power supply to the motor will be reduced in case
of motor overload. With continued motor overload, the
tool will shut off. The switch needs to be cycled (turned
on and off) to restart tool. The tool will power off each
time the current load reaches the overload current value
(motor burn-up point). If continued overload shutdowns
occur, apply less force/weight on the tool until the tool will
function without the overload engaging.
Electronic Soft Start
This feature limits the initial start up momentum, allowing
the speed to build up gradually over a 1 second period.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Attaching Side Handle (Fig. A)

WARNING: Before using the tool, check that the
handle is tightened securely.
Screw the side handle 5 tightly into one of the holes on
either side of the gear case. The side handle should always
be used to maintain control of the tool at all times.
Mounting and Removing Tuckpoint
Shroud (Fig. B)
nOTE: The tuckpoint shroud is only recommended for use
with the DWE46103 heavy-duty small angle grinder.
1. Loosen the collar screw 9
align the tabs 14 on the tuckpoint shroud with the
slots on the grinder gear case.
15
Fig. B
14
2. Rotate the shroud into the desired working position. The
shroud should be positioned between the spindle and
the operator to provide optimum efficiency.
3. Tighten the collar screw
9
shroud on the gear case. Do not operate the grinder
with a loose tuckpoint shroud.
English
on the tuckpoint shroud and
9
15
to secure the tuckpoint
5