Cleaning & Maintenance - Bionaire BCH9212 Manual De Instrucciones

On mode to prevent the heater from cycling.
When the preset temperature is reached or
when the heater is shut off, the fan will run for
15 seconds without heat. This cool down
process ensures an accurate and consistent
temperature reading.
NOTE: To shut the heater off at any setting,
press the Power Button (
Display goes off. The heater will cool down for
15 seconds, and the Fan Only indicator light
will blink in Amber until cool down is completed.
The digital thermostat has memory; it will
remember the last temperature setting before
the heater is turned off. However, if the heater is
unplugged, the digital thermostat will no longer
remember the previous temperature setting. You
will need to reset the digital thermostat if the
heater is unplugged.
Oscillation (if applicable)
Press the Oscillation Button (
panel or remote control (if applicable) to activate
or stop the oscillation feature.
NOTE: Please do not manually turn the heater
on the base. It is designed to turn only by
motorized oscillation.
Timer (if applicable)
Some models are equipped with 24-Hour Auto
Shut-off Timer feature. This allows you to
program your heater to shut off automatically
after running a defined time interval (from 0 to
24 hours).
1. Press the Timer Button (
indicator light will begin to blink for 5
seconds. The LCD Display will show "0"
and the "Hr" icon.
2. Turn the Dial Wheel on the control panel to
adjust from 0 to 24 to select your desired
time interval for the heater to shut-off
automatically. The selected hour will appear
on the LCD Display, and then the Timer
indicator light will stop blinking in 3 seconds
to indicate that the selected timer is
activated. The LCD Display will return to
show the preset temperature and
mode setting.
3. To cancel the Timer feature, press the Timer
Button ( ) twice within 5 seconds, the
Timer indicator light will go off.
NOTE: The timer does not work with the
FrostProtect Setting.
CLEANING/MAINTENANCE
Always unplug the heater before cleaning and
allow the heater to cool down.
1. Clean the unit with a soft cloth moistened
with a mild soap and water solution.
All manuals and user guides at all-guides.com
) until the LCD
) on control
) once. The
5
2. NEVER use abrasive or flammable solvents
to clean the unit.
3. After cleaning, be sure to completely dry the
unit with a cloth or towel.
4. Store heater in a cool, dry location.
5. It is recommended that you store the unit in
its original carton.
TIP: Over time, dust may accumulate on
the front grills. This can be removed by
wiping the unit with a damp cloth.
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-
advanced safety system that requires the user to
reset the heater if there is a potential overheat
situation. When a potential overheat temperature
is reached, the system will automatically shut the
heater off. It can only resume operation when
the user resets the unit.
If the heater shuts down and the Power
Light is flashing:
1. Stand the heater upright.
2. Unplug the heater and allow 30 minutes for
the heater to cool down.
3. After 30 minutes plug the heater in and
operate normally.
4. If the heater does not work normally, repeat
steps 1, 2 and 3 again.
NOTE: If the heater is plugged in again and
Power On/Off Button is pressed within the
30-minute cool down period, heater will run at
Max/2 setting, but shut down in 2 seconds with
the Power Light flashing. Please repeat the
above 4 steps to reset the heater again and
ensure to allow sufficient time for the thermostat
to cool down.
FOR MODELS WITH TIP OVER
PROTECTION
Tip Over Shut-Off:
When the unit is accidentally knocked over, it will
instantly shut off and the Power Light will flash.
The unit may also shut off if it is moved or
bumped. To reset, simply place the heater in an
upright position, the Power Light will stop
flashing and it will operate normally.
NOTE: If unit does not turn on when placed in
the upright position, press Power On/Off Button
once and heater will resume operation.