Publicidad
EN – ASSEMBLY INSTRUCTIONS
Hotdoor heating appliance assembly with HAA11-12
wall attachments
Note: the Hotdoor heating appliance must be assembled and positioned at a
safe distance from walls and flammable objects. Follow the indications
contained in the Hotdoor heating appliance instruction booklet.
1. Pieces contained in the box:
A.
Hotdoor heating appliance
B.
Support tubes B1+B2
C.
Wall plate
D.
Cover
E.
Fitting for electric cable
F.
Four M6 set screws
G.
One M5 screw
H.
One M6 screw with washer
I.
Two M4 screws
J.
Cable with plug
L.
Adhesive disc
You can choose to install the lamp with or without the cable and plug.
If you decide to install the HOTDOOR lamp by connecting it directly to the
electrical system, follow the instructions from point 2 to point 11.
If you decide to install the HOTDOOR lamp by connecting it by means of the cable
and plug, follow the instructions from point 12 to point 22.
ASSEMBLY CONNECTED DIRCTLY TO THE
ELECTRICAL SYSTEM
2. Fix plate C to the wall at the desired height using two correctly-sized wall plugs (not
included) and passing the double-insulated cable coming from the electrical system to
the central slot.
3. Connect watertight fitting E, following the instructions in the packaging of the fitting
and noting the positions of the phase (1), neutral (2) and earth (3) wires.
Note: A double-insulated HAR-type cable (cross-section 3x1.5
2
mm
) with a diameter of 6-9 mm must always come from the
installation in order to avoid any risk of putting the metal parts of
the coupling under tension. If the cable coming from the domestic
installation is not double-insulated, adapt it before mounting the
lamp.
4. Insert the free end of the electric cable coming from lamp A into the entry slot on
support tube B1 and run it through until the silicone sheath coming out of the lamp
(triple protection of the electric cable) is also inserted into the slot.
5. Fix lamp A to the end of support tube B1 by tightening screw H. The screw should
be fitted with the knurled washer provided. After assembly, the screw should be tight
to avoid the lamp from accidentally turning and overheating the walls, potentially
flammable elements or sockets.
6. The cable must pass completely through tube B1 and be inserted and completely
passed through tube B2. Fix tubes B1 and B2 with two screws I.
7. Insert support tubes B1+B2 (that lamp A is mounted on) into the upper hole on plate
C, first passing the cable through and sliding the tube into the lower compartment. Fix
tube B1+B2 to plate C with the four set screws F.
8. Cut the electric cable coming from the lamp to the correct length and connect it to
the other end of the fitting, correctly coupling phase (1), neutral (2) and earth (3).
Tighten the nuts on the fitting so that they are watertight. Then position the fitting in
the free area behind tube B1+B2.
9. Insert cover D from below and fix with screw G.
10. Position the lamp in the desired direction and firmly tighten screw H. If the lamp
(A) does not maintain the desired position, repeat the procedure from step 5, adding
adhesive disc L.
11. The Hotdoor lamp is now assembled and ready to use.
____________________________________________________________________
ASSEMBLY USING
THE CABLE AND PLUG
12. Fix plate C to the wall at the desired height using two correctly-sized wall plugs
(not included) and passing the double-insulated cable coming from the electrical
system to the central slot.
13. Insert the free end of the electric cable coming from lamp A into the entry slot on
support tube B1 and run it through until the silicone sheath coming out of the lamp
(triple protection of the electric cable) is also inserted into the slot.
REV. 02 – 11/2021
14. Fix lamp A to the end of support tube B1 by tightening screw H. The screw should
be fitted with the knurled washer provided. After assembly, the screw should be tight
to avoid the lamp from accidentally turning and overheating the walls, potentially
flammable elements or sockets.
15. The cable must pass completely through tube B1 and be inserted and completely
passed through tube B2. Fix tubes B1 and B2 with two screws I.
16. Insert support tubes B1+B2 (that lamp A is mounted on) into the upper hole on
plate C, first passing the cable through and sliding the tube into the lower
compartment. Fix tube B1+B2 to plate C with the four set screws F.
17. Pierce the top of cover D and insert the cable and plug.
18. Connect watertight fitting E to cable and plug J, following the instructions in the
packaging of the fitting and noting the positions of the phase (1), neutral (2) and earth
(3) wires.
19. Cut the electric cable coming from the lamp to the correct length and connect it to
the other end of the fitting, correctly coupling phase (1), neutral (2) and earth (3).
Tighten the nuts on the fitting so that they are watertight. Then position the fitting in
the free area behind tube B1+B2.
20. Insert cover D from below and fix with screw G.
21. Position the lamp in the desired direction and firmly tighten screw H. If the lamp
(A) does not maintain the desired position, repeat the procedure from step 14, adding
adhesive disc L.
22. The Hotdoor lamp is now assembled and ready to use.
A. Note: The lamp must always be connected to an installation
that can support a power of 2000W. Verify with the installer that
the installation is able to support this power.
Urbani srl reserves the right to all the changes to improve the products also during sales
____________________________________________________________________
DE - MONTAGEANLEITUNG
Montage des Wand-Heizstrahlers Hotdoor HAA11-12
Achtung:
Der
Heizstrahler
Sicherheitsabstand zu Mauern, Wänden und brennbaren Gegenständen
montiert und ausgerichtet werden. Folgen Sie genau den Hinweisen in der
Gebrauchsanleitung für den Heizstrahler Hotdoor.
1. Lieferumfang:
A.
Heizstrahler Hotdoor
B.
Tragrohre B1 + B2
C.
Wandplatte
D.
Abdeckung
E.
Anschluss für Stromkabel
F.
Vier Gewindestifte M6
G.
Eine Schraube M5
H.
Eine Schraube M6 mit Unterlegscheibe
I.
Zwei Schrauben M4
J.
Ein Kabel mit Netzstecker
L.
Eine Klebescheibe
Es besteht die Wahl zwischen dem Betrieb des Gerätes mit Netzstecker oder ohne
Netzstecker:
Wollen Sie den Heizstrahler HOTDOOR direkt an der elektrischen Anlage
betreiben, folgen Sei den Schritten 2 bis 11.
Wollen Sie den Heizstrahler HOTDOOR mittels Kabel mit Netzstecker betreiben,
folgen Sie den Schritten 12 bis 22.
MONTAGE FÜR DEN DIREKTEN BETRIEB AN
DER ELEKTRISCHEN ANLAGE
2. Befestigen Sie die Platte C in der gewünschten Höhe an der Wand, indem Sie zwei
geeignete Spreizdübel (nicht im Lieferumfang enthalten) verwenden und das doppelt
isolierte Kabel der Installation durch den mittleren Schlitz führen.
3.
Schließen
Sie
spritzwassergeschützte
Stromkabel) E an das Stromkabel an, indem Sie die Anweisungen in der Verpackung
befolgen und die Positionen der Phase (1), des Nullleiters (2) und des Schutzleiters
(3) genau beachten.
Achtung: Es muss immer ein doppelt isoliertes Kabel (Querschnitt
2
3x1,5 mm
) vom Typ HAR mit einem Durchmesser von 6-9 mm von
der Anlage kommen, um jedes Risiko zu vermeiden, die Metallteile
der Halterung unter Spannung zu setzen. Wenn das von der
Hausinstallation kommende Kabel nicht doppelt isoliert ist, passen
Sie es vor der Montage des Heizstrahlers an.
Hotdoor
muss
mit
ausreichendem
Verbindungsstück
(Anschluss
für
12
Publicidad
