Publicidad
25. Orientare la lampada nella direzione desiderata e serrare definitivamente la vite H.
Nel caso la lampada (A) non mantenga la posizione desiderata ripetere l'operazione
del punto 18 aggiungendo il discetto adesivo L.
26. La lampada Hotdoor è ora montata e pronta per l'uso.
A . Attenzione: La lampada deve essere sempre collegata ad un
impianto che supporti la potenza di 2000W. Verificare con
l'installatore che il proprio impianto sia adeguato a supportare
tale potenza.
B. attenzione: non utilizzare i cavi con spina J con il connettore
E. Per la commessione con i cavi con spina utilizzare i due
connettori L e commettere separatamente alla linea elettrica.
Urbani srl si riserva il diritto a tutte le modifiche per migliorare i prodotti anche in fase di vendita
EN – ASSEMBLY INSTRUCTIONS
Hotdoor heating appliance assembly with HBA21
attachments
Note: the Hotdoor heating appliance must be assembled and positioned at a safe
distance from walls and flammable objects. Follow the indications contained in the
Hotdoor heating appliance instruction booklet.
Pieces contained in the box:
A.
Two Hotdoor heating appliances
B.
Two support tubes
C.
Plate
D.
Cover
E.
Three-way watertight fitting
F.
Two hexagonal spacers
H.
Six M4 screws
I.
Two M6 screws with washers
J.
Two cables with plug
L.
Two fittings for electric cables
M.
Connection clip
N.
Adhesive disc
You can choose to install the lamp with or without the cable and plug.
If you decide to install the HOTDOOR lamp by connecting it directly to the
electrical system, follow the instructions from point 2 to point 13.
If you decide to install the HOTDOOR lamp by connecting it by means of the cable
and plug, follow the instructions from point 14 to point 26.
ASSEMBLY CONNECTED DIRCTLY TO THE
ELECTRICAL SYSTEM
2. Fix plate C to the ceiling in the desired position using three correctly-sized wall
plugs (not included). Fix clip M to plate C.
3. Pass the power cord coming from the domestic installation through the central slot
on plate C. Connect watertight fitting E to the electrical cable, following the instructions
in the packaging of the fitting and noting the positions of the phase (1), neutral (2) and
earth (3) wires.
Note: A double-insulated HAR-type cable (cross-section 3x2.5
2
mm
) with a diameter of 9-13.5 mm must always come from the
installation in order to avoid any risk of putting the metal parts of
the coupling under tension. If the cable coming from the
domestic installation is not double-insulated, adapt it before
mounting the lamp.
4. For each of the two lamps, insert the free end of the electric cable coming from
lamp A into the entry slot on support tube B and run it through until the silicone sheath
coming out of the lamp (triple protection of the electric cable) is also inserted into the
slot. The cable must completely come out of the other side of the tube.
5. Fix each lamp A to the end of support tube B by tightening screw I. The screw
should be fitted with the knurled washer provided. After assembly, the screw should
be tight to avoid the lamp from accidentally turning and overheating the walls,
potentially flammable elements or sockets. The cable of each lamp must completely
come out of the other side of the tube.
6. Inset cover D onto one of the support tubes B.
7. Lift up the tube complete with lamp and cover (A+B+D) to plate C and fix firmly with
two screws H.
8. Lift up the second tube complete with lamp (A+B) and pass it through the hole in
cover D. Fix firmly with two screws H.
REV. 02 – 11/2021
9. Cut the two cables coming from the lamps to the correct length and connect them to
three-way fitting E, following the instructions provided and being careful to couple
phase to phase, neutral to neutral and earth to earth.
10. Position three-way fitting E in the clip fixed to base C. Apply two spacers F in the
holes in tubes B.
11. Slide cover D along the two tubes B and secure it to the hexagonal spacers with
the two screws H.
12. Position the two lamps in the desired directions and firmly tighten screws I. If the
lamp (A) does not maintain the desired position, repeat the procedure from step 5,
adding adhesive disc N.
14. The Hotdoor double ceiling lamp is now assembled and ready to use.
B. Note: Do not use the cables with plug J with fitting E. To
connect with the cables and plug, use the two fittings L and
connect to the power separately.
ASSEMBLY USING
THE CABLE AND PLUG
14. Fix plate C to the ceiling in the desired position using three correctly-sized wall
plugs (not included). Fix clip M to plate C.
15. Pierce the top of cover D and insert the cables with plug.
16. Connect watertight fittings L to cables with plug J, following the instructions in the
packaging of the fittings and noting the positions of the phase (1), neutral (2) and earth
(3) wires.
17. Insert the free end of the electric cable coming from lamp A into the entry slot on
support tube B and run it through until the silicone sheath coming out of the lamp
(triple protection of the electric cable) is also inserted into the slot. The cable must
completely come out of the other side of the tube.
18. Fix lamp A to the end of support tube B by tightening screw H. The screw should
be fitted with the knurled washer provided. After assembly, the screw should be tight
to avoid the lamp from accidentally turning and overheating the walls, potentially
flammable elements or sockets.
19. Inset cover D onto one of the support tubes B.
20. Lift up the tube complete with lamp and cover (A+B+D) to plate C and fix firmly
with two screws H.
21. Lift up the second tube complete with lamp (A+B) and pass it through the hole in
cover D. Fix firmly with two screws H.
22. Cut the two cables coming from the lamps to the correct length and connect them
to fittings L, following the instructions provided and being careful to couple phase to
phase, neutral to neutral and earth to earth.
23. Position three-way fitting E in the clip fixed to base C. Apply two spacers F in the
holes in tubes B.
24. Slide cover D along the two tubes B and secure it to the hexagonal spacers with
the two screws H.
25. Position the lamp in the desired direction and firmly tighten screw H. If the lamp
(A) does not maintain the desired position, repeat the procedure from step 18, adding
adhesive disc L.
26. The Hotdoor lamp is now assembled and ready to use.
A. Note: The lamp must always be connected to an installation
that can support a power of 2000W. Verify with the installer that
the installation is able to support this power.
B. Note: Do not use the cables with plug J with fitting E. To
connect with the cables and plug, use the two fittings L and
connect to the power separately.
Urbani srl reserves the right to all the changes to improve the products also during sales
20
Publicidad
