Operation - EINHELL PRESSITO Bivolt Manual De Instrucciones Original

In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
5.2 Battery capacity indicator (Fig. 2)
Press the button for the battery capacity indicator
(b). The battery capacity indicator (c) will indicate
the charge status of the battery by means of 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

6.1 Changing between mains/battery operati-
on and compressor compressed air/low-
pressure blower operation (Fig. 7)
To change over between mains-powered and
battery-powered operation, press the selector
switch (10):
•
DC/switch to the right:
•
The equipment will be supplied with power
from the rechargeable battery.
•
AC/switch to the left:
•
The equipment will be supplied with power
from the power cable.
•
To change over between compressed air and
low-pressure operation, press the selector
switch (12):
•
Switch to the left: Compressed air operation
Anl_SA_PRESSITO_Bivolt_SPK8.indb 38 Anl_SA_PRESSITO_Bivolt_SPK8.indb 38
GB
•
Switch in the middle: OFF
•
Switch to the right: Low-pressure operation
6.2 Compressor compressed air operation
(Fig. 1a, 1b, 2, 7)
•
To inflate objects with compressed air, use
the compressed air hose (5).
•
Connect the adapter of the compressed air
hose to the object you wish to inflate.
•
Depending on what you are inflating, also use
the adapters (7, 8, 9) or other adapters availa-
ble from retail stores.
•
The pressure at the compressed air hose will
be displayed in the display (11).
•
The unit of the displayed pressure can be se-
lected with the button (15). The pressure can
be displayed in units of [bar], [PSI] or [kPa].
•
The button (14) allows the desired pressure
to be reduced.
•
The button (16) allows the desired pressure
to be increased.
•
Switch on the equipment by moving the se-
lector switch (12) to the compressed air ope-
ration position (see 6.1.).
•
The compressor will then pump until the pre-
set pressure on the display is reached, then it
will switch off.
•
Warning! Observe the information supplied
by the tire manufacturer and the vehicle ma-
nufacturer relating to the recommended tire
pressure.
•
Warning! This equipment is not calibrated!
For a calibrated measurement value, check
the actual tire pressure using a calibrated me-
ter after you have inflated the tires yourself,
e.g. at a petrol station.
•
Just before it is switched off, the pressure
which is shown in the display can be 0.05 –
0.2 bar higher than the preselected pressure,
because of overpressure in the air hose.
•
Allow the compressor to cool down for about
5 minutes after every 5 minutes of operation
in order to prevent overheating.
6.3 Low-pressure blower operation
(Fig. 1a, 3, 4)
6.3.1 Suctioning air (Fig. 3, 7)
•
To suction out objects with a large volume
until they are empty (e.g. deflating an air
mattress, etc.), connect the air hose (3) to the
extractor connection (13).
•
Connect the air hose to the object you wish
to deflate.
•
Switch on the equipment by moving the se-
- 38 -
15.10.2018 10:59:20 15.10.2018 10:59:20