Removing/Inserting The Battery - Milwaukee M18 FORCE LOGIC 2877-20 Manual Del Operador

Anderson*
Splice
VACS
Model #'s
Lug
VACL
Model #'s
Str Wire
Size Range
(Code only)
#6 AWG
#4 AWG
#2 AWG
#1 AWG
1/0 AWG
2/0 AWG
3/0 AWG
4/0 AWG
250 MCM
300 MCM
350 MCM
400 MCM
500 MCM
600 MCM
750 MCM
A single crimp should be centered in the middle of the crimping area. Number of crimps is a minimum. Additional crimps would not negatively affect the
integrity of the connection so long as they are uniformly placed between the intended crimp area of the connector, typically outlined with color bands or knurls.
For the latest listing of approvals, visit milwaukeetool.com. For technical or service assistance, contact Milwaukee Customer Service at 1-800-729-3878.
*NOTE: Anderson does not manufacture #6 AWG Dual Rated Lugs or #t AWG Copper Splices.
SPECIFICATIONS
Cat. No. ..................................................... 2877-20
Volts .............................................................. 18 DC
Battery Type .................................................M18™
Charger Type ................................................M18™
Module/FCC ID ......... 5123A-BLE113/QOQBLE113
Operating Temp ..................................... 0° - 122° F
Capacity....................................#6-750 MCM Cu/Al
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always lock the trigger or remove
WARNING
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To avoid damage to the tool, do not
CAUTION
operate the tool without the nest
being fully closed and latched.
An incomplete or faulty crimp could
WARNING
cause a fire. Use tool only with
connectors for which they are rated. Tool and
connectors must be used in an approved com-
bination to achieve a successful operation. Im-
proper combinations can result in a faulty crimp.
Electric shock, fire, explosion, and property
damage could occur.
Dual Rated Lugs & Splices with COPPER Wire
Blackburn Burndy
®
ASP YS-A
ATL YA-A
YA-ATN
Anderson* Blackburn
1-Splices Only
1
1
ILSCO
AS
ASN
ACL, 2ACL,
ACN, 2ACN,
ALND, ALNS,
ALNN
Lugs: Total # of Crimps
Splices: # of Crimps per Side
® Burndy ILSCO
1 1
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store
or Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Blinking Blue Tool is actively communicating with
Blinking Red Tool is in security lockout and can
WARNING
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken first.
Keep hands away from crimping jaws
while tool is in use. Fingers could be
crushed.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
5
Panduit Penn-Union
SA BCUA
LAA BLUA
LAB
Panduit Penn-Union
1
ONE-KEY™
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
the ONE-KEY™ app.
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of arc flash,
electric shock and property
T&B
60501-60578
60101-60178
60230-60278
T&B
1 1