Milwaukee M18 FORCE LOGIC 2877-20 Manual Del Operador página 6

Crimping
Before crimping:
• Inspect the crimping ram, nest and clevis for cracks
or other damage. Do not use damaged parts. Con-
tact a MILWAUKEE service facility.
• Ensure the nest is properly latched.
• Connectors and cables must be used in an AP-
PROVED COMBINATION. Improper combinations
can result in a faulty crimp.
• Inspect and discard workpieces with cracks or wear
before use. Materials may crack or shatter.
• Follow installation specifications as specified in Table
A using an Approved Combination of connectors and
cables as indicated. Other uses may cause damage
to the tool and workpiece.
1. Insert battery pack.
2. Place the ram and nest around the connector.
3. Hold tool securely. Press and hold the trigger.
4. When the cycle is complete the tool will auto
retract and the indicator will light. Release the trigger.
LED
Indicator Definition
Solid Green Tool completed the operation and
reached full specified distance.
Solid Red Tool completed the operation but did NOT
reach full specified distance.
Flashing Red Tool did NOT complete the operation.
Flashing Tool has reached its service interval
Red/Green (40,000 crimps). Red/Green flashing
will begin after the solid Red or Green
(after Solid
indicator for the operation is displayed.
Green or
MILWAUKEE
Solid Red)
tool be inspected and preventative
maintenance completed. Return tool to
MILWAUKEE service facility.
a
5. Continue crimping according to the instructions in
Table A or the connector manufacturer's installa-
tion instructions.
• Crimps should be uniformly placed on the barrel
of the connector with a single crimp placed in the
center.
• Crimps should be reasonably placed within the
color bands or knurled area of the connector.
6. Two LEDs will light the workpiece when the trigger
is pulled.
7. The tool identifier is pressed into the connector
during the crimp.
Backup Release Valve
If the ram needs to be opened without completing
the cycle, press and hold the backup release valve.
Hold tool securely until the cylinder retracts fully.
NOTE: If the indenter has made contact with the con-
nector and the backup release valve is used, the tool
will register the attempt as an unsuccessful crimp.
recommends that the
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
ONE-KEY™
Refer to the ONE-KEY App for information regarding
necessary servicing, such as internal battery life and
crimp count.
Chemical Burn Hazard.
WARNING
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en-
tered the body, seek immediate medical attention.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
6
Cleaning
any vents. Keep tool