Installation Precautions - Nice NEXT SOLAR KIT Instrucciones Y Advertencias Para La Instalación Y El Uso

GENERAL WARNINGS: SAFETY - INSTALLATION - USE (instructions translated from Italian)
WARNING Important safety instructions. Observe all the instructions as improper installation may cause serious damage
WARNING Important safety instructions. It is important to comply with these instructions to ensure personal safety. Store
these instructions
• Before commencing the installation, check the "Product technical specifications", in particular whether this product is suitable for automating
your guided part. Should it be unsuitable, DO NOT proceed with the installation
• The product cannot be used before it has been commissioned as specified in the "Testing and commissioning" chapter
WARNING According to the most recent European legislation, the implementation of an automation system must comply with
the harmonised standards set forth in the Machinery Directive in force, which allow for declaring the presumed
conformity of the automation. On account of this, all operations regarding connection to the mains electricity, as
well as product testing, commissioning and maintenance, must be performed exclusively by a qualified and skilled
technician!
• Before proceeding with the product's installation, check that all materials are in good working order and are suitable for the intended applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone lack-
ing sufficient experience or familiarity with the product
• Children must not play with the appliance
• Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children
WARNING In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered
through an external switching device, such as a timer, or connected to a supply that is regularly powered or switched off by
the circuit
• Handle the product with care during installation, taking care to avoid crushing, knocks, falls or contact with liquids of any kind. Keep the
product away from sources of heat and open flames. Failure to observe the above can damage the product and increase the risk of danger
or malfunctions. If this should happen, stop installation immediately and contact the Customer Service
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty does not cover material defects
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before intervening on the system (maintenance, cleaning), always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not
use if repairs or adjustments are necessary, because a failure with the installation or an incorrectly balanced automated system may lead to
injury
• The packaging materials of the product must be disposed of in compliance with local regulations
• There must be at least 0.4 m between the driven parts and any fixed elements
• The wording on the tubular motors can be covered after assembly
• Motor with removable power supply cable with dedicated connector: if the power supply cable is damaged, it must be replaced by the
manufacturer or by the latter's technical assistance service, or nonetheless by a similarly qualified person, so as to prevent any risk
• Be careful with moving shutters and keep away from them until they have lowered fully
• Do not activate the awning when maintenance activities – such as window cleaning – are being carried out nearby
• Disconnect the awning from the power supply when maintenance activities – such as window cleaning – are being carried out nearby.
Warning for "shades with automatic control"
• Prior to installing the drive motor, remove any unnecessary cables and disable any appliance not required for motorised operation
• Install the manoeuvring assembly for manual release at a height below 1.8 m
NOTE: if removable, the manoeuvring assembly must be kept close to the door
• Make sure that the controls are kept at a safe distance from moving parts, while allowing a good view of these.
The manoeuvring assembly of a switch kept manually closed must be located in a position that is visible from the guided part but far from
moving parts. It must be installed at a minimum height of 1.5 m
• The fixed control devices must be installed in a visible position
• For drive motors that allow for accessing unprotected moving parts once they have been installed, such parts must be installed 2.5 m above
the floor or other surface from which they can be accessed
• Failure to observe the following rules can cause a fire or the battery to explode
• Use the battery exclusively for its intended use
• Protect the battery against heat sources and from water
• Do not charge nor use batteries that have fallen or are damaged
• Do not connect the battery's positive or negative pole with metal objects
• Charge the battery using the battery charger/power supply unit supplied as an accessory under supervision
• Do not open the battery compartment and do not make changes to it
• The battery's efficiency decreases after prolonged use or if the battery is charged frequently
• Charge the battery using the power supply/battery charger supplied separately
Note for reading this Manual – Some of the figures referred to in the text appear at the end of the manual.
6 – English

INSTALLATION PRECAUTIONS

BATTERY